Frequency response of a common-emitter amplifier
To design a voltage-divider biased CE amplifier and plot its frequency response to find mid-band gain and bandwidth.
- Transistor BC547
- Resistors for biasing (e.g. R1 47 kΩ, R2 10 kΩ, RC 2.2 kΩ, RE 470 Ω)
- Capacitors 10 µF (coupling), 100 µF (bypass)
- Function generator
- CRO
- DC supply 12 V
Theory
The CE amplifier gives a phase-inverted output with gain Av ≈ −RC / re′ (with RE bypassed). At low frequencies the coupling and bypass capacitors reduce the gain; at high frequencies the transistor's internal capacitances do. The bandwidth is the range between the lower and upper −3 dB frequencies: BW = fH − fL.
Read the lesson: Mosfet switching ›- 12 V → R1 → base → R2 → ground; 12 V → RC → collector; emitter → RE → ground with CE across it
- Input through 10 µF to the base; output through 10 µF from the collector
Procedure
Pre-lab check
4 questions · 75% to be readyTry the readings before the lab
| f (Hz) | Gain | Gain (dB) |
|---|---|---|
| 10 | 12.4 | 21.9 |
| 31 | 36.6 | 31.3 |
| 99 | 77.8 | 37.8 |
| 312 | 96.9 | 39.7 |
| 981 | 99.7 | 40 |
| 3087 | 100 | 40 |
| 9717 | 99.9 | 40 |
| 30580 | 99.5 | 40 |
| 96241 | 95.2 | 39.6 |
| 302887 | 70.4 | 36.9 |
| 953238 | 30 | 29.5 |
| 3000000 | 10 | 20 |
Precautions
- Keep the input small enough that the output is not clipped.
- Check the bias point before applying a signal.
My readings
Type what you measured. It goes into your record book, and to My Garage when you are signed in.
| S. No. | f (Hz) | Gain | Gain (dB) |
|---|---|---|---|
| 1 | |||
| 2 | |||
| 3 | |||
| 4 | |||
| 5 | |||
| 6 |
Check my readings
Put the value you set in the first column, then compare. Real parts have tolerance.
Mid-band gain = ___ (___ dB), fL = ___ Hz, fH = ___ kHz, bandwidth = ___ kHz.
Everything above is free. The print-ready write-up comes with Maker.
Printed pages leave the observation table empty for your own readings.
Viva questions
Say your answer out loud first, then check. The first 2 answers are free; Maker opens all 4.
Quick answers for your record and viva
What is the aim of the frequency response of a common-emitter amplifier experiment?
To design a voltage-divider biased CE amplifier and plot its frequency response to find mid-band gain and bandwidth.
What apparatus is needed for frequency response of a common-emitter amplifier?
Transistor BC547, Resistors for biasing (e.g. R1 47 kΩ, R2 10 kΩ, RC 2.2 kΩ, RE 470 Ω), Capacitors 10 µF (coupling), 100 µF (bypass), Function generator, CRO, DC supply 12 V.
What is the theory behind frequency response of a common-emitter amplifier?
The CE amplifier gives a phase-inverted output with gain Av ≈ −RC / re′ (with RE bypassed). At low frequencies the coupling and bypass capacitors reduce the gain; at high frequencies the transistor's internal capacitances do. The bandwidth is the range between the lower and upper −3 dB frequencies: BW = fH − fL.
What result should I get in frequency response of a common-emitter amplifier?
Mid-band gain = ___ (___ dB), fL = ___ Hz, fH = ___ kHz, bandwidth = ___ kHz.
What precautions should I take in frequency response of a common-emitter amplifier?
Keep the input small enough that the output is not clipped. Check the bias point before applying a signal.
