Lab / MAKAUT / Electronic devices / Experiment 4

Diode clippers and clampers

Electronic devicesVirtual readings4 viva questionsRecord book ready
Aim

To build positive and negative clippers and a positive clamper, and observe their output waveforms.

Apparatus
  • Function generator
  • Diodes 1N4148
  • Resistor 10 kΩ
  • Capacitor 1 µF
  • DC supply for the reference
  • CRO

Theory

A clipper removes the part of a signal above (or below) a level. In a shunt positive clipper with reference Vref, the output cannot rise above Vref + 0.7 V because the diode conducts. A clamper shifts the whole waveform up or down without changing its shape: a capacitor charges to the peak through the diode, so a positive clamper output swings from about −0.7 V to 2Vm − 0.7 V.

Read the lesson: Diodes protection ›
Circuit connections
  • Clipper: input → 10 kΩ → output; diode (anode at output) in series with Vref from output to ground
  • Clamper: input → capacitor → output; diode from output to ground (anode to ground for positive clamping); 100 kΩ load

Procedure

Pre-lab check

4 questions · 75% to be ready
1What is the difference between a clipper and a clamper?
2Why is a clamper called a DC restorer?
3What decides the clipping level?
4What condition must RC meet in a clamper?

Try the readings before the lab

Calculated, not measured. In the lab, write down your own readings.
-6.14-22.156.310090180270360Phase (°)V
Vin (V)Clipper out (V)Clamper out (V)
Phase (°)Vin (V)Clipper out (V)Clamper out (V)
0004.3
302.52.56.8
604.332.78.63
9052.79.3
1204.332.78.63
1502.52.56.8
180004.3
210-2.5-2.51.8
240-4.33-4.33-0.03
270-5-5-0.7
300-4.33-4.33-0.03
330-2.5-2.51.8
360004.3

Precautions

  • Use DC coupling on the CRO to see the clamper's shift.
  • Choose RC much longer than the signal period for the clamper.

My readings

Type what you measured. It goes into your record book, and to My Garage when you are signed in.

S. No.Phase (°)Vin (V)Clipper out (V)Clamper out (V)
1
2
3
4
5
6

Check my readings

Put the value you set in the first column, then compare. Real parts have tolerance.

Open my record book
Result

The clipper limits the output at ___ V (Vref + 0.7 V). The clamper shifts the waveform up by ___ V while keeping its shape.

Everything above is free. The print-ready write-up comes with Maker.

Printed pages leave the observation table empty for your own readings.

Viva questions

Say your answer out loud first, then check. The first 2 answers are free; Maker opens all 4.

1. What is the difference between a clipper and a clamper?
2. Why is a clamper called a DC restorer?
3. What decides the clipping level?
4. What condition must RC meet in a clamper?

Quick answers for your record and viva

What is the aim of the diode clippers and clampers experiment?

To build positive and negative clippers and a positive clamper, and observe their output waveforms.

What apparatus is needed for diode clippers and clampers?

Function generator, Diodes 1N4148, Resistor 10 kΩ, Capacitor 1 µF, DC supply for the reference, CRO.

What is the theory behind diode clippers and clampers?

A clipper removes the part of a signal above (or below) a level. In a shunt positive clipper with reference Vref, the output cannot rise above Vref + 0.7 V because the diode conducts. A clamper shifts the whole waveform up or down without changing its shape: a capacitor charges to the peak through the diode, so a positive clamper output swings from about −0.7 V to 2Vm − 0.7 V.

What result should I get in diode clippers and clampers?

The clipper limits the output at ___ V (Vref + 0.7 V). The clamper shifts the waveform up by ___ V while keeping its shape.

What precautions should I take in diode clippers and clampers?

Use DC coupling on the CRO to see the clamper's shift. Choose RC much longer than the signal period for the clamper.

Diode clippers and clampers: lab experiment, theory and viva