Tools / Transistor voltage-divider bias

How to work out transistor voltage-divider bias

Two resistors fix the base voltage and an emitter resistor keeps the current steady even when the transistor's gain varies.

Vth = Vcc·R2 ÷ (R1+R2); Ib = (Vth − Vbe) ÷ (Rth + (β+1)Re); Ic = βIb; Vce = Vcc − IcRc − IeRe

Inputs

V
Ω
Ω
Ω
Ω
×
V

Results update as you type. Prefixes work: 4.7k, 100u, 10n.

Result
Collector current
1.286 mA
Base voltage
1.999 V
Emitter voltage
1.299 V
Vce
7.871 V
Region
Active
Ic change
7.803 %
Step by step

The working with your numbers

  1. Thevenin equivalent of the dividerVth = Vcc × R2 ÷ (R1 + R2) = 2.11 V, Rth = R1 ∥ R2 = 8.25 kΩ
  2. Base currentIb = (Vth − Vbe) ÷ (Rth + (β + 1) × Re) = (2.11 − 0.7) ÷ (8,246 + 101 × 1,000) = 12.9 µAThe (β + 1) × Re term is why the emitter resistor stabilises the bias.
  3. Collector currentIc = β × Ib = 100 × 1.29 × 10⁻⁵ = 1.29 mA
  4. Emitter and base voltagesVe = Ie × Re = 1.3 V, Vb = Ve + Vbe = 2 V
  5. Collector-emitter voltageVce = Vcc − Ic × Rc − Ie × Re = 12 − 2.83 − 1.3 = 7.87 V
  6. Where it sitsActiveA good amplifier bias puts Vce at about half the supply, so the signal can swing both ways.

Does the answer make sense?

  • OK: Region: Active. Vce = 7.87 V is away from half of the supply.
  • OK: Stiff divider rule: Rth (8.25 kΩ) should be under 10 % of (β + 1) × Re (10.1 kΩ). It is, so Ic barely depends on β.
  • OK: If hFE falls to 50 or rises to 200, Ic moves from 1.19 mA to 1.34 mA.

Pick a real part

  • Standard E24 parts for Rc and Re: 2.2 kΩ and 1 kΩ. Use 1 % resistors for R1 and R2 so the bias point does not wander.
  • Use a transistor rated for more than 12 V and for the collector current, such as a BC547 (45 V, 100 mA) or 2N2222.

Common mistakes

  • Drawing the base current from the divider and forgetting it. A very high R1 or R2 lets the base current pull the divider down. Keep Rth small compared with β × Re.
  • Leaving out Re. Without it Ic follows β, which varies hugely between parts and with temperature.
  • Biasing near a rail. If Vce is under 1 V or over Vcc − 1 V, the signal clips.

Learn it, try it, build it

Calculated, not measured. Check the exact part datasheet and your real circuit before powering anything.

Common questions

How do you bias a transistor with a voltage divider?

Find the divider's Thevenin voltage and resistance, then Ib = (Vth − Vbe) ÷ (Rth + (β + 1) × Re), Ic = β × Ib and Vce = Vcc − Ic × Rc − Ie × Re. Aim for Vce about half of Vcc.

Why add an emitter resistor?

It gives negative feedback. If hFE rises, Ic rises, the voltage across Re rises, the base-emitter voltage falls and the current is pulled back, so Ic hardly depends on hFE.