Projects / Yogurt box thermometer

Yogurt box thermometer

Beginner1.8 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. PICODS18B2025.3°C

    Wire the probe

    Red to 3V3(OUT), black to GND, yellow to GP16, 4.7 kilo-ohms from yellow to 3V3(OUT).

  2. PICO

    Wire the display

    VCC, GND, SDA to GP0, SCL to GP1.

  3. PICO

    Wire the buzzer

    Plus to GP15, minus to GND.

  4. PICO13.8 mASSD1306

    Install the ssd1306 module

    From Thonny's Manage packages.

  5. PICO

    Run the program

    The display shows the temperature.

  6. PICODS18B2025.4°C

    Hold the probe in warm tap water

    The value rises.

  7. PICO

    Put it in cool water for a minute

    It shows Too cool and then beeps.

In short

How do you build a yogurt box thermometer?

A waterproof DS18B20 probe in an insulated box of warm water watches the temperature that keeps the milk warm during yogurt making, and a Pico beeps if it drops below a set value. It monitors only and does not heat anything. You need Raspberry Pi Pico H, DS18B20 waterproof probe, Resistor 4.7 kΩ, SSD1306 OLED Display, Passive buzzer and Breadboard 830 Tie Points. It takes 7 steps and about 110 minutes.

Level
Beginner
Time
About 110 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
DS18B20 red (VCC)Pico 3V3(OUT) pin 36Power at 3.3 V
DS18B20 black (GND)Pico GND pin 38Common ground
DS18B20 yellow (data)Pico GP16 pin 21One-wire data
4.7 kilo-ohm resistorBetween the data wire and 3V3(OUT)Pull-up for the data line
OLED VCCPico 3V3(OUT) pin 36Power at 3.3 V
OLED GNDPico GND pin 38Common ground
OLED SDA and SCLPico GP0 pin 1 and GP1 pin 2I2C0 data and clock
Passive buzzer +Pico GP15 pin 20Tone output
Passive buzzer -Pico GND pin 38Return

Code

Yogurt is made by keeping warm milk with a live culture at a steady warm temperature for several hours, and the usual range is between about 38 and 46 degrees. Many people use an insulated box or a cool box filled with warm water. This build is only a thermometer that watches the water bath and warns you when it has cooled too far or is too hot, so you can top it up. It does not heat anything. The DS18B20 is a digital temperature probe that sends its reading over one wire, and the program uses the onewire and ds18x20 modules that come with MicroPython. The probe has a waterproof case, but it is not made for food, so keep it in the water bath and not in the milk. The pull-up resistor holds the data line high. The program only beeps after the temperature has been out of range for thirty seconds, so opening the lid for a moment does not set it off. Follow proper food hygiene with milk, clean the jars well and throw away anything that smells or looks wrong. The thermometer is indicative and is not a food safety device.

import time
import onewire
import ds18x20
import ssd1306
from machine import Pin, I2C, PWM

LOW_C = 38.0                                        # beep if the water bath falls below this
HIGH_C = 46.0                                       # and if it rises above this
CHECK_SECONDS = 30                                  # must stay out of range this long before beeping

i2c = I2C(0, sda=Pin(0), scl=Pin(1), freq=400000)
oled = ssd1306.SSD1306_I2C(128, 64, i2c)
buzzer = PWM(Pin(15))
buzzer.duty_u16(0)

sensor = ds18x20.DS18X20(onewire.OneWire(Pin(16)))
roms = sensor.scan()
if not roms:
    raise RuntimeError("No DS18B20 found, check the wires and the pull-up resistor")

def beep(times):
    for _ in range(times):
        buzzer.freq(2000)
        buzzer.duty_u16(20000)
        time.sleep_ms(200)
        buzzer.duty_u16(0)
        time.sleep_ms(200)

out_of_range_since = None
while True:
    sensor.convert_temp()
    time.sleep_ms(800)                              # the probe needs 750 ms to measure
    t = sensor.read_temp(roms[0])

    if t < LOW_C:
        status = "Too cool"
    elif t > HIGH_C:
        status = "Too hot"
    else:
        status = "In range"

    if status == "In range":
        out_of_range_since = None
    else:
        if out_of_range_since is None:
            out_of_range_since = time.time()
        if time.time() - out_of_range_since >= CHECK_SECONDS:
            beep(3 if status == "Too cool" else 5)
            out_of_range_since = time.time()        # repeat the beeps every 30 seconds

    oled.fill(0)
    oled.text("Yogurt box", 0, 0)
    oled.text("%.1f C" % t, 0, 20)
    oled.text(status, 0, 40)
    oled.text("%d to %d C" % (LOW_C, HIGH_C), 0, 54)
    oled.show()
    time.sleep(2)

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Probe in warm waterTemperature and In range
Probe in cold waterToo cool
Wait 30 seconds out of rangeBeeps three times
Probe in very hot water from the tapToo hot, five beeps
Back to rangeBeeps stop

If it does not work

No DS18B20 found

Check the three wires and the 4.7 kilo-ohm pull-up.

Reads 85 degrees

The probe has just started, wait for the next reading.

Display blank

Check the OLED address 0x3C and that ssd1306.py is on the Pico.

No beep

Check the buzzer is passive and on GP15.

Temperature looks wrong

Check the probe is not touching the side of the box or a heater.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the yogurt box thermometer?

Raspberry Pi Pico H, DS18B20 waterproof probe, Resistor 4.7 kΩ, SSD1306 OLED Display, Passive buzzer and Breadboard 830 Tie Points.

How long does the yogurt box thermometer take to build?

About 110 minutes for a beginner maker, in 7 steps.

How do I know the yogurt box thermometer works?

Probe in warm water: Temperature and In range. Probe in cold water: Too cool. Wait 30 seconds out of range: Beeps three times.

No DS18B20 found: what should I check?

Check the three wires and the 4.7 kilo-ohm pull-up.

Reads 85 degrees: what should I check?

The probe has just started, wait for the next reading.

Display blank: what should I check?

Check the OLED address 0x3C and that ssd1306.py is on the Pico.

No beep: what should I check?

Check the buzzer is passive and on GP15.