Projects / Water use monitor

Water use monitor

Intermediate2 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. ESP32

    Wire the sensor

    Connect power, ground and the divided signal.

  2. ESP32

    Test the count

    Blow gently through it and watch pulses print.

  3. ESP32S201

    Fit it in the line

    Put the arrow along the flow.

  4. ESP32

    Calibrate

    Pour 10 litres and set PULSES_PER_LITRE.

  5. ESP32

    Fill in the Wi-Fi

    Replace the placeholders.

  6. ESP32

    Upload

    Open the page at the board's address.

  7. ESP32S201

    Test the leak rule

    Temporarily change the night hours and run water for five minutes.

  8. ESP32

    Mount

    Keep the board dry.

In short

How do you build a water use monitor?

A flow sensor on a garden or tank line counts litres and shows daily use and leaks on a web page. You need ESP32 DevKit V1, Water flow sensor YF-S201, 5 V 2 A USB adapter, Resistor 1 kΩ and Resistor 2 kΩ. It takes 8 steps and about 120 minutes.

Level
Intermediate
Time
About 120 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Flow sensor red wire5 V supply +Power, 5 to 18 V
Flow sensor black wire5 V supply - and ESP32 GNDGround
Flow sensor yellow wire1 kΩ resistor then ESP32 GPIO27, with 2 kΩ from GPIO27 to GNDDivider brings 5 V pulses down to about 3.3 V
5 V supplyESP32 VINPower the ESP32 too

Code

The sensor's Hall switch makes about 450 pulses for each litre, but it varies between sensors, so calibrate: pour a measured 10 litres through it and set PULSES_PER_LITRE to the pulses counted divided by 10. The sensor works at 5 V and makes 5 V pulses, so a 1 kΩ and 2 kΩ divider reduces them to about 3.3 V for the ESP32. Fit it in a straight section of pipe with the arrow along the flow and use it only for low pressure garden or tank lines; it is not a billing meter. Flow for five minutes without a break at night, when nobody uses water, is a good sign of a leak. Keep the electronics dry away from the pipe. Arduino IDE with the ESP32 boards package, board "ESP32 Dev Module".

Runs on a virtual ESP32 Dev Module in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Counts pulses from a YF-S201 (about 450 pulses per litre), shows litres on a web page.
#include <WiFi.h>
#include <WebServer.h>
#include <time.h>

const char* WIFI_SSID = "YOUR_WIFI_NAME";
const char* WIFI_PASS = "YOUR_WIFI_PASSWORD";
const float PULSES_PER_LITRE = 450.0;      // calibrate with a measured bucket
const byte FLOW_PIN = 27;
volatile unsigned long pulses = 0;
unsigned long lastPulses = 0, litreTotalPulses = 0, lastCheck = 0;
unsigned long flowSeconds = 0;             // consecutive seconds with flow
bool leakFlag = false;
int lastDay = -1;
WebServer server(80);

void IRAM_ATTR onPulse() { pulses++; }

void handleRoot() {
  float litres = litreTotalPulses / PULSES_PER_LITRE;
  String s = "<html><body style='font-family:sans-serif'><h3>Water today</h3><p>" + String(litres, 1) + " litres</p>";
  s += leakFlag ? "<p style='color:red'>Possible leak: flow at night</p>" : "<p>No leak flagged</p>";
  s += "</body></html>";
  server.send(200, "text/html", s);
}

void setup() {
  Serial.begin(115200);
  pinMode(FLOW_PIN, INPUT);
  attachInterrupt(digitalPinToInterrupt(FLOW_PIN), onPulse, RISING);
  WiFi.begin(WIFI_SSID, WIFI_PASS);
  while (WiFi.status() != WL_CONNECTED) delay(300);
  configTime(19800, 0, "pool.ntp.org");
  server.on("/", handleRoot);
  server.begin();
  Serial.println(WiFi.localIP());
}

void loop() {
  server.handleClient();
  if (millis() - lastCheck >= 1000) {
    lastCheck = millis();
    noInterrupts(); unsigned long p = pulses; interrupts();
    unsigned long d = p - lastPulses; lastPulses = p;
    litreTotalPulses += d;
    time_t t = time(nullptr); struct tm* tm = localtime(&t);
    if (tm->tm_year > 100) {
      if (tm->tm_mday != lastDay) { lastDay = tm->tm_mday; litreTotalPulses = 0; leakFlag = false; }  // new day
      flowSeconds = d > 3 ? flowSeconds + 1 : 0;
      bool night = tm->tm_hour >= 2 && tm->tm_hour < 4;
      if (night && flowSeconds > 300) leakFlag = true;       // five minutes of flow at 2 to 4 am
    }
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
10 litres pouredAbout 10 litres on the page
Tap offNo pulses
Flow for 5 minutes at nightLeak flag
New dayTotal resets to zero

If it does not work

No pulses

Check the divider and the 5 V supply on the sensor.

Reads high or low

Recalibrate the pulses per litre.

Page does not open

Check the IP address and the Wi-Fi.

Time wrong

The NTP server needs internet access.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the water use monitor?

ESP32 DevKit V1, Water flow sensor YF-S201, 5 V 2 A USB adapter, Resistor 1 kΩ and Resistor 2 kΩ.

How long does the water use monitor take to build?

About 120 minutes for a intermediate maker, in 8 steps.

How do I know the water use monitor works?

10 litres poured: About 10 litres on the page. Tap off: No pulses. Flow for 5 minutes at night: Leak flag.

No pulses: what should I check?

Check the divider and the 5 V supply on the sensor.

Reads high or low: what should I check?

Recalibrate the pulses per litre.

Page does not open: what should I check?

Check the IP address and the Wi-Fi.

Time wrong: what should I check?

The NTP server needs internet access.