Build it step by step
0 of 7 doneBuild the 555 oscillator
A few kHz square wave.
Add the pump capacitor
From the output through to the diodes.
Add the diodes
Orientation matters.
Add the output capacitor
10 µF with voltage rating above 16 V.
Measure with no load
About twice the supply less drops.
Load it
Watch the voltage fall.
Compare
Read about the ICL7660.
How do you build a voltage doubler?
Diodes and capacitors double a square wave's voltage, the idea behind charge pumps. You need NE555 Timer IC, Signal Diode 1N4148 × 2, Electrolytic capacitor 10 µF × 3, Resistor 1 kΩ × 2, Ceramic capacitor 10 nF, Breadboard 830 Tie Points, 9 V battery and 9 V battery snap with DC jack. It takes 7 steps and about 45 minutes.
- Level
- Intermediate
- Time
- About 45 min
- Parts
- 8
Parts list
- Integrated CircuitsBuyNE555 Timer IC × 1
- SemiconductorsBuy
- PassivesBuy
- PassivesBuyResistor 1 kΩ × 2
- PassivesBuy
- PrototypingBuy
- BatteriesBuy9 V battery × 1
- PowerBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| 9 V battery | NE555 pin 8 and pin 1 | Power |
| 555 pins 2 and 6 joined | 1 kΩ and 10 nF timing network | Astable at a few kHz |
| 555 pin 3 | 10 µF capacitor | Square wave out |
| Capacitor other end | Between two 1N4148 diodes | Pump node |
| First diode cathode | Supply plus | Clamp to the rail |
| Second diode anode | Pump node, cathode to the output capacitor | Output |
| Output 10 µF capacitor | Ground | Reservoir |
No code needed
When the 555 output goes low, the first diode charges the pump capacitor to about the supply minus a diode drop. When the output goes high, the capacitor's lower end rises by the supply voltage, pushing the node to nearly twice the supply, and the second diode passes that charge to the output capacitor. In practice you get about twice the supply minus two diode drops, so about 16 V from 9 V, and the voltage falls as you load it, because it can only deliver a few milliamps. Do not connect anything sensitive; this is a teaching circuit. The charge-pump ICs in the lab, such as the ICL7660, work on the same idea with better switches. Keep the supply to a 9 V battery and watch the output capacitor rating, since 16 V can exceed a small capacitor's rating.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| No load | About 14 to 16 V from a 9 V battery |
| 1 kΩ load | Voltage falls sharply |
| Diode reversed | No doubling |
| Higher frequency | Slightly lower ripple |
If it does not work
Output low
Check diode direction and capacitor values.
No oscillation
Check the 555 wiring.
Capacitor gets warm
Reduce the load.
Output wobbles
Increase the output capacitor.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the voltage doubler?
NE555 Timer IC, Signal Diode 1N4148 × 2, Electrolytic capacitor 10 µF × 3, Resistor 1 kΩ × 2, Ceramic capacitor 10 nF, Breadboard 830 Tie Points, 9 V battery and 9 V battery snap with DC jack.
How long does the voltage doubler take to build?
About 45 minutes for a intermediate maker, in 7 steps.
How do I know the voltage doubler works?
No load: About 14 to 16 V from a 9 V battery. 1 kΩ load: Voltage falls sharply. Diode reversed: No doubling.
Output low: what should I check?
Check diode direction and capacitor values.
No oscillation: what should I check?
Check the 555 wiring.
Capacitor gets warm: what should I check?
Reduce the load.
Output wobbles: what should I check?
Increase the output capacitor.
