Projects / Sunshine hours recorder

Sunshine hours recorder

Beginner1.3 hGuided buildReviewed

Build it step by step

0 of 6 done
  1. NANO509 lux

    Wire the LDR

    Build the divider and print readings to find sunny and cloudy values.

  2. NANO

    Choose the threshold

    Set it between a sunny and a cloudy reading.

  3. NANODS323114:28PCF8574

    Add the clock and display

    Wire the DS3231 and LCD.

  4. NANO511 lux

    Run indoors

    Shine a torch on the LDR to see Today increase.

  5. NANO

    Mount outside

    Fix it facing up in a clear dome on a post or roof.

  6. NANO

    Compare days

    Note the totals against what you saw of the weather.

In short

How do you build a sunshine hours recorder?

An LDR facing the sky counts how many minutes a day the sun is bright enough to cast shadows, a classic weather station measurement. You need Arduino Nano, LDR Photoresistor, Resistor 10 kΩ, DS3231 RTC module and 16x2 LCD with I2C backpack (PCF8574). It takes 6 steps and about 75 minutes.

Level
Beginner
Time
About 75 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
5VLDR leg 1Top of the divider
LDR leg 2Nano A0 and 10 kΩ resistor to GNDLight reading
DS3231 SDA, SCLNano A4, A5I2C
LCD SDA, SCLNano A4, A5I2C, same bus
DS3231 and LCD VCC, GNDNano 5V, GNDPower

Code

Arduino IDE, board "Arduino Nano" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones). Install "RTClib" and "LiquidCrystal I2C". Set the DS3231 once with RTClib's example. Mount the LDR facing the sky in a clear dome or under a clear cover so rain cannot reach the electronics, away from shade, and tilt it level. An LDR is not a calibrated instrument: official sunshine recorders use a threshold of about 120 W/m², so use this one to compare days with each other rather than as an exact figure. Find THRESHOLD by printing the reading on a sunny and a cloudy afternoon.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <Wire.h>
#include <RTClib.h>
#include <LiquidCrystal_I2C.h>
#include <EEPROM.h>

RTC_DS3231 rtc;
LiquidCrystal_I2C lcd(0x27, 16, 2);
const int THRESHOLD = 750;                  // reading above this counts as bright sun; set it from your own sunny and cloudy readings
const byte LDR = A0;
unsigned long today = 0, yesterday = 0;     // seconds of bright sun
byte day = 0;
unsigned long lastSave = 0;

void setup() {
  rtc.begin();
  lcd.init(); lcd.backlight();
  EEPROM.get(0, today); EEPROM.get(4, yesterday); day = EEPROM.read(8);
  if (today > 86400UL) today = 0;
  if (yesterday > 86400UL) yesterday = 0;
  if (day > 31) day = rtc.now().day();
}

void loop() {
  long s = 0;
  for (byte i = 0; i < 10; i++) { s += analogRead(LDR); delay(20); }
  if (s / 10 > THRESHOLD) today += 10;                    // adds ten seconds each time it is bright

  DateTime n = rtc.now();
  if (n.day() != day) { yesterday = today; today = 0; day = n.day(); EEPROM.put(4, yesterday); EEPROM.update(8, day); }
  if (millis() - lastSave > 3600000UL) { EEPROM.put(0, today); lastSave = millis(); }   // save hourly so a power cut loses little

  lcd.setCursor(0, 0); lcd.print("Today "); lcd.print(today / 3600.0, 1); lcd.print(" h    ");
  lcd.setCursor(0, 1); lcd.print("Yest. "); lcd.print(yesterday / 3600.0, 1); lcd.print(" h    ");
  delay(9800);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Torch on the LDRToday rises by 10 s every cycle
Shadow over itToday stops rising
MidnightYesterday takes today's value and today resets
Power cutToday resumes within an hour of its last save

If it does not work

Always counting

Threshold is too low. Raise it above a cloudy reading.

Never counts

Threshold is too high or the LDR faces the wrong way.

Date does not roll

Set the DS3231 time.

LCD blank

Check the I2C address and contrast.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the sunshine hours recorder?

Arduino Nano, LDR Photoresistor, Resistor 10 kΩ, DS3231 RTC module and 16x2 LCD with I2C backpack (PCF8574).

How long does the sunshine hours recorder take to build?

About 75 minutes for a beginner maker, in 6 steps.

How do I know the sunshine hours recorder works?

Torch on the LDR: Today rises by 10 s every cycle. Shadow over it: Today stops rising. Midnight: Yesterday takes today's value and today resets.

Always counting: what should I check?

Threshold is too low. Raise it above a cloudy reading.

Never counts: what should I check?

Threshold is too high or the LDR faces the wrong way.

Date does not roll: what should I check?

Set the DS3231 time.

LCD blank: what should I check?

Check the I2C address and contrast.