Projects / Tipping-bucket rain gauge

Tipping-bucket rain gauge

Intermediate3 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. NANO

    Print the parts

    Print a funnel, a see-saw bucket and a frame.

  2. NANO4.98V

    Fix the magnet and switch

    Glue the magnet to the arm and place the reed switch so it closes once per tip.

  3. NANO

    Test the switch

    Tip the bucket by hand and watch the count rise by one each time.

  4. NANODS323116:54PCF8574

    Wire the Nano

    Connect the RTC, LCD and reed switch as in the table.

  5. NANODS323117:55

    Upload the sketch

    Set the RTC time using an example sketch once.

  6. NANO

    Calibrate

    Pour 100 ml slowly through the funnel and note the tips, then work out mm per tip.

  7. NANO

    Update MM_PER_TIP

    Enter the calibrated value in the sketch.

  8. NANO

    Install

    Mount it level outdoors and check it after rain.

In short

How do you build a tipping-bucket rain gauge?

A 3D-printed tipping bucket with a magnet and reed switch counts each 0.2 mm of rain and an Arduino totals daily rainfall. You need Arduino Nano, Reed switch (glass, 2 × 14 mm), Neodymium magnets (10 × 3 mm) × 2, DS3231 RTC module, 16x2 LCD with I2C backpack (PCF8574), Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm) and 3D printer PLA filament 1.75 mm (1 kg). It takes 8 steps and about 180 minutes.

Level
Intermediate
Time
About 180 min
Parts
8

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Reed switchNano D2 and GNDCounts tips, uses the internal pull-up
DS3231 module VCCNano 5VPower
DS3231 module GNDNano GNDGround
DS3231 module SDANano A4I2C data
DS3231 module SCLNano A5I2C clock
LCD I2C VCCNano 5VPower
LCD I2C GNDNano GNDGround
LCD I2C SDANano A4I2C data, shared
LCD I2C SCLNano A5I2C clock, shared

Code

The mm of rain per tip is the volume of one bucket divided by the funnel area. For a funnel of 100 cm² and a bucket that tips at 2 ml, each tip is 2 ÷ 100 × 10 = 0.2 mm. Measure your own funnel and calibrate by pouring a known volume slowly through it. Fix the magnet on the see-saw arm so that it passes the reed switch once per tip, and seal the electronics against water. Keep the gauge level and away from trees and walls, with the funnel at least a metre above the ground. A tipping bucket under-reads in very heavy rain, so treat the result as a good estimate and not a reference. Arduino IDE, board "Arduino Nano" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones).

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Libraries: RTClib (Adafruit), LiquidCrystal_I2C (Frank de Brabander).
#include <Wire.h>
#include <RTClib.h>
#include <LiquidCrystal_I2C.h>
#include <EEPROM.h>

const float MM_PER_TIP = 0.2;           // change after calibration
volatile unsigned int tips = 0;
volatile unsigned long lastTip = 0;
unsigned int savedTips = 0;
byte savedDay = 0;

RTC_DS3231 rtc;
LiquidCrystal_I2C lcd(0x27, 16, 2);     // try 0x3F if blank

void onTip() {
  unsigned long n = millis();
  if (n - lastTip > 50) { tips++; lastTip = n; }     // 50 ms debounce
}

void saveState(byte day) {
  EEPROM.put(0, savedTips);
  EEPROM.update(4, day);
}

void setup() {
  pinMode(2, INPUT_PULLUP);
  attachInterrupt(digitalPinToInterrupt(2), onTip, FALLING);
  lcd.init(); lcd.backlight();
  rtc.begin();
  DateTime now = rtc.now();
  EEPROM.get(0, savedTips);
  savedDay = EEPROM.read(4);
  if (savedDay != now.day() || savedTips == 0xFFFF) { savedTips = 0; savedDay = now.day(); saveState(savedDay); }
  tips = savedTips;
}

void loop() {
  DateTime now = rtc.now();
  if (now.day() != savedDay) {          // new day, reset the total
    noInterrupts(); tips = 0; interrupts();
    savedTips = 0; savedDay = now.day(); saveState(savedDay);
  }
  noInterrupts(); unsigned int t = tips; interrupts();
  if (t != savedTips) { savedTips = t; saveState(savedDay); }   // EEPROM is rated for about 100000 writes

  lcd.setCursor(0, 0);
  lcd.print("Today ");
  lcd.print(t * MM_PER_TIP, 1);
  lcd.print(" mm   ");
  lcd.setCursor(0, 1);
  lcd.print(now.hour()); lcd.print(":");
  if (now.minute() < 10) lcd.print("0");
  lcd.print(now.minute());
  lcd.print("  tips "); lcd.print(t); lcd.print("  ");
  delay(500);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Bucket tipped by handCount rises by one
100 ml poured slowlyA consistent number of tips
Power cycleToday's total is restored
After midnightTotal resets to zero

If it does not work

Count jumps by two or more

Increase the debounce or move the magnet.

No count

Check the reed switch position and the D2 wire.

LCD blank

Try address 0x3F and adjust the contrast trimmer.

Total wrong

Recalibrate MM_PER_TIP with a measured volume.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the tipping-bucket rain gauge?

Arduino Nano, Reed switch (glass, 2 × 14 mm), Neodymium magnets (10 × 3 mm) × 2, DS3231 RTC module, 16x2 LCD with I2C backpack (PCF8574), Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm) and 3D printer PLA filament 1.75 mm (1 kg).

How long does the tipping-bucket rain gauge take to build?

About 180 minutes for a intermediate maker, in 8 steps.

How do I know the tipping-bucket rain gauge works?

Bucket tipped by hand: Count rises by one. 100 ml poured slowly: A consistent number of tips. Power cycle: Today's total is restored.

Count jumps by two or more: what should I check?

Increase the debounce or move the magnet.

No count: what should I check?

Check the reed switch position and the D2 wire.

LCD blank: what should I check?

Try address 0x3F and adjust the contrast trimmer.

Total wrong: what should I check?

Recalibrate MM_PER_TIP with a measured volume.