Projects / Stop at ten seconds challenge

Stop at ten seconds challenge

Press a button to start a hidden stopwatch and press again when you think ten seconds have passed, and the display shows how close you got.

Beginner1.5 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. NANO

    Wire the display

    CLK to D6, DIO to D7, with 5V and GND.

  2. NANO

    Wire the button

    D2 to GND.

  3. NANO

    Wire the buzzer

    D8 and GND.

  4. NANO12:45

    Install the library

    TM1637Display from the Library Manager.

  5. NANO

    Upload the sketch

    The display shows 00:00.

  6. NANO

    Press once

    The clock runs for two seconds, then hides.

  7. NANO

    Press at ten seconds

    Your time and error are shown.

  8. NANO

    Play again

    A press resets, the best score stays.

In short

How do you build a stop at ten seconds challenge?

Press a button to start a hidden stopwatch and press again when you think ten seconds have passed, and the display shows how close you got. You need Arduino Nano, TM1637 4-digit display, Tactile push button 6 mm, Passive buzzer, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points. It takes 8 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
TM1637 CLKNano D6Display clock
TM1637 DIONano D7Display data
TM1637 VCC and GNDNano 5V and GNDPower
Button leg 1Nano D2Start and stop input
Button leg 2Nano GNDPressed pulls D2 low
Passive buzzer positiveNano D8Result beeps
Passive buzzer negativeNano GNDCommon ground

Code

Estimating ten seconds without a clock is harder than it sounds. In this game the stopwatch is visible for only the first two seconds and then the display shows dashes, so you must keep time in your head. Press the button once to start and again when you think ten seconds have passed. The Nano measures the real elapsed time with millis, which counts milliseconds from power-up, and then shows two numbers in turn: your time in seconds, using the colon of the display as a decimal point, and your error in hundredths of a second, where a minus sign means you stopped early. A result within 0.05 seconds earns a happy double beep. The sketch is a small state machine with three states, idle, running and result, and a press moves it from one to the next. The buttons are debounced with a 40 millisecond lockout. The best error so far is kept in memory and printed on the serial monitor so you can compete with friends. Try counting out loud, tapping a foot or closing your eyes, and see which method works best.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <TM1637Display.h>

TM1637Display disp(6, 7);                     // CLK, DIO
const int BTN = 2, BUZZ = 8;
const unsigned long TARGET_MS = 10000UL;
const unsigned long SHOW_FOR_MS = 2000UL;     // the clock is visible for the first two seconds only

enum State { IDLE, RUNNING, RESULT };
State state = IDLE;
unsigned long startMs = 0, stopMs = 0, elapsed = 0;
long errorMs = 0;
long bestAbsError = 99999;
bool wasPressed = false;
unsigned long lastPress = 0;

void showTime(unsigned long ms) {
  unsigned int hundredths = (unsigned int)min(ms / 10UL, 9999UL);
  disp.showNumberDecEx(hundredths, 0b01000000, true);   // colon works as the decimal point: 10:00 is 10.00 s
}

void showHidden() {
  const uint8_t dashes[] = {0x40, 0x40, 0x40, 0x40};
  disp.setSegments(dashes);
}

void setup() {
  pinMode(BTN, INPUT_PULLUP);
  disp.setBrightness(4);
  Serial.begin(9600);
  showTime(0);
  Serial.println("Press to start. Press again at 10.00 seconds.");
}

void loop() {
  bool pressed = (digitalRead(BTN) == LOW);
  bool edge = pressed && !wasPressed && (millis() - lastPress > 40);
  wasPressed = pressed;
  if (edge) lastPress = millis();

  if (state == IDLE) {
    if (edge) { startMs = millis(); state = RUNNING; tone(BUZZ, 1200, 60); }
  } else if (state == RUNNING) {
    unsigned long t = millis() - startMs;
    if (t < SHOW_FOR_MS) showTime(t); else showHidden();
    if (edge) {
      stopMs = millis();
      elapsed = stopMs - startMs;
      errorMs = (long)elapsed - (long)TARGET_MS;
      if (abs(errorMs) < bestAbsError) bestAbsError = abs(errorMs);
      state = RESULT;
      if (abs(errorMs) <= 50) { tone(BUZZ, 1800, 150); delay(200); tone(BUZZ, 2200, 250); }
      else tone(BUZZ, 500, 200);
      Serial.print("Time "); Serial.print(elapsed / 1000.0, 2);
      Serial.print(" s, error "); Serial.print(errorMs / 1000.0, 2);
      Serial.print(" s, best "); Serial.print(bestAbsError / 1000.0, 2); Serial.println(" s");
    }
  } else {                                      // RESULT: alternate time and error every 2 seconds
    unsigned long phase = ((millis() - stopMs) / 2000UL) % 2;
    if (phase == 0) showTime(elapsed);
    else disp.showNumberDec((int)(errorMs / 10), false);   // signed hundredths of a second, minus means early
    if (edge) { state = IDLE; showTime(0); }
  }
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

Press to start. Press again at 10.00 seconds.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Power onDisplay shows 00:00
First pressClock counts for two seconds then shows dashes
Stop at exactly 10.00 sDisplay shows 10:00 and the error 0
Stop at 9.80 sShows 09:80 then an error of -20
Serial monitorTime, error and best error printed

If it does not work

Display blank

Check CLK on D6 and DIO on D7 and the 5V wire.

Button seems to start and stop at once

Increase the 40 millisecond lockout.

Digits look odd

The colon is used as a decimal point, so 10:00 means 10.00 seconds.

No beep

Use a passive buzzer on D8.

Timing is wrong

Check the sketch uses millis and the button is on D2.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the stop at ten seconds challenge?

Arduino Nano, TM1637 4-digit display, Tactile push button 6 mm, Passive buzzer, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points.

How long does the stop at ten seconds challenge take to build?

About 90 minutes for a beginner maker, in 8 steps.

How do I know the stop at ten seconds challenge works?

Power on: Display shows 00:00. First press: Clock counts for two seconds then shows dashes. Stop at exactly 10.00 s: Display shows 10:00 and the error 0.

Display blank: what should I check?

Check CLK on D6 and DIO on D7 and the 5V wire.

Button seems to start and stop at once: what should I check?

Increase the 40 millisecond lockout.

Digits look odd: what should I check?

The colon is used as a decimal point, so 10:00 means 10.00 seconds.

No beep: what should I check?

Use a passive buzzer on D8.