Projects / Function generator with DDS

Function generator with DDS

Intermediate2.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANO

    Wire the module

    SPI and power.

  2. NANO

    Set a frequency

    Write the three words.

  3. NANO

    Check on a scope or sound card

    Confirm 1 kHz.

  4. NANO

    Add the encoder

    Change the frequency.

  5. NANO

    Add the step and shape buttons

    Click and long press.

  6. NANO

    Add the display

    Show frequency and shape.

  7. NANO

    Add the level pot

    Output through a capacitor.

In short

How do you build a function generator with DDS?

A DDS module makes sine, square and triangle waves from 1 Hz to 1 MHz, set with an encoder. You need Arduino Nano, Function generator (DDS), Rotary encoder module (KY-040), SSD1306 OLED Display, Potentiometer 10 kΩ and Electrolytic capacitor 10 µF. It takes 7 steps and about 150 minutes.

Level
Intermediate
Time
About 150 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
AD9833 VCC and GNDNano 5V and GNDPower
AD9833 FSYNCNano D10Chip select
AD9833 SCLKNano D13SPI clock
AD9833 SDATANano D11SPI data
AD9833 OUT10 uF to the top of a 10 k potOutput (wiper is the signal)
Encoder CLK and DTNano D2 and D3Rotation
Encoder SWNano D4Button, to GND when pressed
OLED SDA and SCLNano A4 and A5I2C

Code

Direct digital synthesis builds a wave by counting through a table of numbers very fast, and the number you write sets how quickly it counts, which sets the frequency. The AD9833 chip does this with a 25 MHz clock, so the Nano only has to send three 16-bit words over SPI to change the frequency. The sine and triangle come out around 0.6 V peak to peak, and the square wave swings the full supply; the pot after the capacitor lets you turn the level down, and the capacitor removes the small DC offset. The output is weak and can only drive a high-impedance input such as an oscilloscope or an amplifier; a speaker will not work directly. A proper buffer needs an op-amp on a dual supply, which is left out here. Frequencies over a few hundred kilohertz show the limits of the 25 MHz clock: the wave has fewer points per cycle, so check it on a scope. Mind that the module is for lab use, not for connecting to mains or a mains-powered device. Arduino IDE, board "Arduino Nano" (try the Old Bootloader option if the upload fails).

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// DDS function generator: AD9833 over SPI, KY-040 encoder to set the frequency, click to change the step, long press for the shape.
// Libraries: Adafruit SSD1306, Adafruit GFX. Board: Arduino Nano. Most AD9833 modules have a 25 MHz crystal.
#include <SPI.h>
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
const byte FSYNC = 10, CLK_PIN = 2, DT_PIN = 3, SW_PIN = 4;
const float MCLK = 25000000.0;
long freq = 1000;
const long STEPS[] = {1, 10, 100, 1000, 10000, 100000};
byte stepIdx = 3;
byte wave = 0;                               // 0 sine, 1 triangle, 2 square
const char* NAMES[] = {"Sine", "Triangle", "Square"};
volatile int delta = 0;
void write16(uint16_t w) {
  SPI.beginTransaction(SPISettings(1000000, MSBFIRST, SPI_MODE2));
  digitalWrite(FSYNC, LOW); SPI.transfer16(w); digitalWrite(FSYNC, HIGH);
  SPI.endTransaction();
}
void setOutput() {
  uint32_t word = (uint32_t)((double)freq * 268435456.0 / MCLK);       // 2^28 / MCLK
  uint16_t ctrl = 0x2000;                                                // B28: two writes make one frequency word
  if (wave == 1) ctrl |= 0x0002; else if (wave == 2) ctrl |= 0x0028;
  write16(ctrl);
  write16(0x4000 | (word & 0x3FFF));
  write16(0x4000 | ((word >> 14) & 0x3FFF));
}
void isr() { delta += (digitalRead(DT_PIN) != digitalRead(CLK_PIN)) ? 1 : -1; }
void show() {
  oled.clearDisplay(); oled.setTextColor(SSD1306_WHITE);
  oled.setTextSize(2); oled.setCursor(0, 0); oled.print(freq); oled.print(" Hz");
  oled.setTextSize(1); oled.setCursor(0, 30); oled.print(NAMES[wave]);
  oled.setCursor(0, 44); oled.print("Step "); oled.print(STEPS[stepIdx]); oled.print(" Hz");
  oled.display();
}
void setup() {
  pinMode(FSYNC, OUTPUT); digitalWrite(FSYNC, HIGH);
  pinMode(CLK_PIN, INPUT_PULLUP); pinMode(DT_PIN, INPUT_PULLUP); pinMode(SW_PIN, INPUT_PULLUP);
  SPI.begin();
  write16(0x0100);                                                      // reset
  attachInterrupt(digitalPinToInterrupt(CLK_PIN), isr, FALLING);
  oled.begin(SSD1306_SWITCHCAPVCC, 0x3C);
  setOutput(); show();
}
void loop() {
  static unsigned long pressedAt = 0;
  noInterrupts(); int d = delta; delta = 0; interrupts();
  if (d != 0) { freq = constrain(freq + d * STEPS[stepIdx], 1L, 1000000L); setOutput(); show(); }
  if (!digitalRead(SW_PIN)) { if (pressedAt == 0) pressedAt = millis(); }
  else if (pressedAt) {
    if (millis() - pressedAt > 600) { wave = (wave + 1) % 3; setOutput(); }
    else stepIdx = (stepIdx + 1) % 6;
    pressedAt = 0; show(); delay(50);
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
1 kHz sineScope shows 1 kHz within 0.1 percent
ClickStep changes
Long pressShape changes
Turn to 100 kHzFrequency follows

If it does not work

No output

Check FSYNC and that the module has power.

Wrong frequency

Check the module crystal frequency.

Distorted wave

Use a high-impedance load.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the function generator with DDS?

Arduino Nano, Function generator (DDS), Rotary encoder module (KY-040), SSD1306 OLED Display, Potentiometer 10 kΩ and Electrolytic capacitor 10 µF. Function generator (DDS): Or an AD9833 module.

How long does the function generator with DDS take to build?

About 150 minutes for a intermediate maker, in 7 steps.

How do I know the function generator with DDS works?

1 kHz sine: Scope shows 1 kHz within 0.1 percent. Click: Step changes. Long press: Shape changes.

No output: what should I check?

Check FSYNC and that the module has power.

Wrong frequency: what should I check?

Check the module crystal frequency.

Distorted wave: what should I check?

Use a high-impedance load.