Projects / Shower timer for saving water

Shower timer for saving water

Beginner1.5 hGuided buildReviewed

Build it step by step

0 of 6 done
  1. NANOS20117.1 mA

    Wire the sensor and display

    Flow sensor to 5V, GND and D2, display to D4 and D5, LED to D9 to D11.

  2. NANOS201

    Bench-test the flow sensor

    Blow gently through it. The pulse count rises with a short Serial print.

  3. NANO

    Fit it inline

    Use the correct threaded fittings and PTFE tape. Put the sensor between the tap and the shower hose, not inside the wet area.

  4. NANOS201

    Calibrate

    Run the water into a 10 litre bucket and note the pulse count. Divide by 10 for pulses per litre.

  5. NANO17.1 mA

    Box and mount

    Put the Nano and display in a sealed box fixed outside the splash zone.

  6. NANOS201

    Test a shower

    Turn on the water. The display counts time and litres and turns red after five minutes.

In short

How do you build a shower timer for saving water?

A waterproof box with a water flow sensor times your shower and shows litres used, flashing red after five minutes. You need Arduino Nano, Water flow sensor YF-S201, TM1637 4-digit display, RGB LED 5 mm common cathode, Resistor 220 Ω × 3, Battery holder 4 × AA with switch, AA alkaline battery × 4 and Jumper wires male to male (40 pcs, 20 cm). It takes 6 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
8

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Flow sensor redNano 5VSupply
Flow sensor blackNano GNDGround
Flow sensor yellow (signal)Nano D2Pulse input on an interrupt
TM1637 CLK and DIONano D4 and D5Display
TM1637 VCC and GNDNano 5V and GNDSupply
RGB LED red, green, blue legsNano D9, D10, D11 through 220 Ω eachStatus colour
RGB LED common cathodeNano GNDCommon cathode type
4 AA packNano VIN and GND6 V from batteries

Code

Arduino IDE, board "Arduino Nano" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones). Install "TM1637" by Avishay Orpaz. The display alternates between minutes and seconds, and litres multiplied by ten. Calibrate PULSES_PER_LITRE by filling a 10 litre bucket and dividing the counted pulses by 10. Keep the electronics in a sealed box away from spray, and place only the flow sensor in the pipe.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <TM1637Display.h>

const byte FLOW = 2, R = 9, G = 10;
TM1637Display display(4, 5);
volatile unsigned long pulses = 0;
const float PULSES_PER_LITRE = 450.0;        // YF-S201 typical, calibrate with a bucket
unsigned long startMs = 0, lastPulseMs = 0, lastCount = 0;
bool showering = false;

void onPulse() { pulses++; }

void setup() {
  pinMode(FLOW, INPUT_PULLUP);
  pinMode(R, OUTPUT); pinMode(G, OUTPUT);
  display.setBrightness(5);
  attachInterrupt(digitalPinToInterrupt(FLOW), onPulse, FALLING);
}

void loop() {
  noInterrupts(); unsigned long p = pulses; interrupts();
  if (p != lastCount) {                       // water is flowing
    lastCount = p; lastPulseMs = millis();
    if (!showering) { showering = true; startMs = millis(); noInterrupts(); pulses = 0; interrupts(); p = 0; lastCount = 0; }
  }
  if (showering && millis() - lastPulseMs > 60000UL) showering = false;   // idle for a minute: ready for the next one

  unsigned long secs = showering ? (lastPulseMs - startMs) / 1000 : 0;
  float litres = p / PULSES_PER_LITRE;
  if (millis() / 3000 % 2 == 0) display.showNumberDecEx((secs / 60) * 100 + secs % 60, 0b01000000, true);   // mm:ss
  else display.showNumberDec((int)(litres * 10));                                                              // litres x 10

  if (showering && secs > 300) {              // over five minutes: flash red
    bool on = (millis() / 400) % 2;
    digitalWrite(R, on); digitalWrite(G, LOW);
  } else {
    digitalWrite(R, LOW); digitalWrite(G, showering);
  }
  delay(100);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Water onLED goes green and time counts
After 5 minutesLED flashes red
10 litres into a bucketDisplay reads close to 10 litres
Water off for a minuteReady for the next use

If it does not work

Litres off by 10 to 20 percent

Calibrate with a bucket, because flow rate changes the count a little.

No pulses

Check the flow direction arrow on the sensor and the signal wire on D2.

Display not changing

CLK and DIO are swapped.

Leak at the fitting

Re-do the PTFE tape and tighten by hand plus a quarter turn.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the shower timer for saving water?

Arduino Nano, Water flow sensor YF-S201, TM1637 4-digit display, RGB LED 5 mm common cathode, Resistor 220 Ω × 3, Battery holder 4 × AA with switch, AA alkaline battery × 4 and Jumper wires male to male (40 pcs, 20 cm).

How long does the shower timer for saving water take to build?

About 90 minutes for a beginner maker, in 6 steps.

How do I know the shower timer for saving water works?

Water on: LED goes green and time counts. After 5 minutes: LED flashes red. 10 litres into a bucket: Display reads close to 10 litres.

Litres off by 10 to 20 percent: what should I check?

Calibrate with a bucket, because flow rate changes the count a little.

No pulses: what should I check?

Check the flow direction arrow on the sensor and the signal wire on D2.

Display not changing: what should I check?

CLK and DIO are swapped.

Leak at the fitting: what should I check?

Re-do the PTFE tape and tighten by hand plus a quarter turn.