Projects / Visitor counter at the door

Visitor counter at the door

Beginner1.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANOmotion

    Test the PIR

    Wave a hand and print the pin.

  2. NANOBC547

    Add the transistor

    Clean 5 V signal.

  3. NANODS323121:59

    Set the clock

    DS3231 example sketch.

  4. NANO

    Count visits

    Ignore repeats for 3 seconds.

  5. NANO

    Write the CSV

    One line per hour.

  6. NANO8.0 mASSD1306

    Show the totals

    OLED hour and day.

  7. NANO

    Chart the data

    Bars per hour in a spreadsheet.

In short

How do you build a visitor counter at the door?

A PIR logs visitors at a shop door by hour and shows a graph. You need Arduino Nano, AM312 mini PIR motion sensor, DS3231 RTC module, MicroSD Card Module, SanDisk microSD card 32 GB (A1, Class 10), SSD1306 OLED Display, BC547 NPN transistor and Resistor 10 kΩ × 2. It takes 7 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
8

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
AM312 VCC and GNDNano 5V and GNDPower
AM312 OUT10 kΩ to BC547 baseLevel translation
BC547 emitterGroundGround
BC547 collectorNano D2, with 10 kΩ to 5VActive-low motion signal
RTC and OLED SDA, SCLNano A4 and A5Shared I2C bus
SD module CSNano D10Chip select
SD module MOSI, MISO, SCKNano D11, D12, D13SPI
SD module VCC and GNDNano 5V and GNDPower

Code

The AM312's output is only about 3 V, which a 5 V Nano can read unreliably, so a BC547 transistor turns it into a clean 5 V signal that goes low when someone passes. Each hour the sketch appends a line to visits.csv on the SD card, and you can open it in a spreadsheet and draw the daily bar chart there; the OLED shows the current hour and the day's count. One person lingering at the door counts once per three seconds, so treat the numbers as foot traffic, not exact heads. The sensor counts movement and records no images or identities, but if the counter covers a public area, tell visitors in a small notice. Set the DS3231 clock once with the RTClib example. Arduino IDE, board "Arduino Nano" (try the Old Bootloader option if the upload fails).

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Door visitor counter: logs one CSV line per hour. Libraries: RTClib, SD, U8g2 (text-only U8x8 to save RAM).
#include <Wire.h>
#include <SPI.h>
#include <SD.h>
#include <RTClib.h>
#include <U8x8lib.h>
RTC_DS3231 rtc;
U8X8_SSD1306_128X64_NONAME_HW_I2C oled(U8X8_PIN_NONE);
const int PIR = 2, CS = 10;
unsigned int hourCount = 0, dayCount = 0;
int curHour = -1, curDay = -1;
unsigned long lastHit = 0;
void flushHour(DateTime t) {                         // append "date,hour,count" to the card
  File f = SD.open("visits.csv", FILE_WRITE);
  if (f) {
    f.print(t.year()); f.print("-"); f.print(t.month()); f.print("-"); f.print(t.day()); f.print(",");
    f.print(curHour); f.print(","); f.println(hourCount);
    f.close();
  }
}
void show() {
  oled.setCursor(0, 0); oled.print("Hour: "); oled.print(hourCount); oled.print("    ");
  oled.setCursor(0, 2); oled.print("Today: "); oled.print(dayCount); oled.print("    ");
}
void setup() {
  pinMode(PIR, INPUT);
  rtc.begin(); SD.begin(CS);
  oled.begin(); oled.setFont(u8x8_font_chroma48medium8_r);
  curHour = rtc.now().hour(); curDay = rtc.now().day();
  show();
}
void loop() {
  DateTime now = rtc.now();
  if (now.hour() != curHour) { flushHour(now); hourCount = 0; curHour = now.hour(); }
  if (now.day() != curDay) { dayCount = 0; curDay = now.day(); }
  if (digitalRead(PIR) == LOW && millis() - lastHit > 3000UL) {   // ignore repeats for 3 s
    lastHit = millis(); hourCount++; dayCount++; show();
  }
  delay(50);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Walk pastCount goes up by one
Wave for 2 secondsCounts once
Hour changesNew CSV line is written
Power cycleSD file keeps the history

If it does not work

Never counts

Check the transistor orientation.

Counts constantly

Aim the sensor away from fans and sunlight.

SD fails

Format the card as FAT32.

Wrong hours

Reset the clock.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the visitor counter at the door?

Arduino Nano, AM312 mini PIR motion sensor, DS3231 RTC module, MicroSD Card Module, SanDisk microSD card 32 GB (A1, Class 10), SSD1306 OLED Display, BC547 NPN transistor and Resistor 10 kΩ × 2.

How long does the visitor counter at the door take to build?

About 90 minutes for a beginner maker, in 7 steps.

How do I know the visitor counter at the door works?

Walk past: Count goes up by one. Wave for 2 seconds: Counts once. Hour changes: New CSV line is written.

Never counts: what should I check?

Check the transistor orientation.

Counts constantly: what should I check?

Aim the sensor away from fans and sunlight.

SD fails: what should I check?

Format the card as FAT32.

Wrong hours: what should I check?

Reset the clock.