Projects / PWM fan hub for a PC case

PWM fan hub for a PC case

Beginner2 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. NANO12DCLM2596

    Set the buck converter

    Connect the 12 V adapter to the LM2596 only and turn the screw until the output reads 5.0 V.

  2. NANOLM2596

    Wire the 5 V rail

    LM2596 output to the Nano 5V and GND pins, with the Nano unplugged from USB.

  3. NANODS18B2028.8°C

    Wire the sensor

    DS18B20 to 5V, GND and D2 with the 4.7 k between D2 and 5V.

  4. NANO18.5 mASSD1306

    Wire the OLED

    SDA to A4, SCL to A5, 5V and GND.

  5. NANOIRLZ44

    Wire the MOSFET stage

    Gate to D3 through 220 ohms, 10 k from gate to source, source to ground, fans between 12 V and the drain, diode across them.

  6. NANODS18B2028.9°C

    Upload the sketch

    The screen shows the temperature and a fan speed.

  7. NANO

    Warm the probe in your hand

    The fan percentage climbs as the reading rises.

  8. NANO

    Unplug the probe

    The screen says NO PROBE and the fans go to full speed.

In short

How do you build a PWM fan hub for a PC case?

A DS18B20 temperature probe and a MOSFET make four 12 V case fans quieter when the box is cool and faster as it warms up. The screen shows the temperature and fan speed, and the fans go to full speed if the probe is ever lost. You need Arduino Nano, 12 V DC fan 80 mm × 4, DS18B20 Temperature Sensor, Resistor 4.7 kΩ, MOSFET IRLZ44N, Resistor 220 Ω, Resistor 10 kΩ, Rectifier Diode 1N4007, SSD1306 OLED Display, 12 V 2 A DC adapter, DC barrel to screw terminal adapter (female), LM2596 Buck Module, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 8 steps and about 120 minutes.

Level
Beginner
Time
About 120 min
Parts
14

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
12 V adapterScrew terminal adapterThe only 12 V supply
Terminal + and -LM2596 IN+ and IN-Set OUT to 5.0 V with no load before connecting the Nano
LM2596 OUT+ and OUT-Nano 5V and GNDPowers the Nano and the OLED
Four fans, red wiresTerminal +Fans run in parallel at 12 V
Four fans, black wiresMOSFET drain (middle leg)The MOSFET switches the ground side
1N4007Stripe to terminal +, other end to the drainAbsorbs spikes from the fan coils
MOSFET sourceTerminal - and Nano GNDAll grounds are joined
MOSFET gate220 ohm to Nano D3PWM pin
10 k from gate to sourceGate to GNDKeeps the fans off while the Nano restarts
DS18B20 red, black and yellowNano 5V, GND and D2Put it in the case, away from the fans
4.7 kBetween D2 and 5VThe pull-up the sensor needs
OLED SDA and SCLNano A4 and A5I2C data and clock
OLED VCC and GNDNano 5V and GNDPower for a 0.96 inch module

Code

The sketch reads the temperature once a second and turns it into a fan speed with a straight line. At 30 degrees or below the fans run at about 35 percent, at 55 degrees or above they run flat out, and in between the speed rises smoothly. That is called a fan curve, and every PC fan controller uses one. The slowest speed is not zero because a fan that is turned down too far stops turning and does not restart by itself. The MOSFET is the switch: the Nano pin D3 sends pulses, called PWM, to its gate, and the longer each pulse, the more power the fans get. The 10 k resistor from gate to ground keeps the fans off while the Nano is starting, the 220 ohm resistor protects the pin, and the 1N4007 diode soaks up the voltage spike that a spinning fan coil makes when the switch opens. The most important line is the fail-safe: if the probe wire comes loose the library returns -127, and the sketch then sets full speed instead of leaving the fans slow in a hot box. Install "OneWire", "DallasTemperature", "Adafruit SSD1306" and "Adafruit GFX" from the Library Manager. Set the LM2596 to 5.0 V with a multimeter before you connect the Nano. Four fans at 12 V draw roughly one amp, which a 2 A adapter handles. Try changing T_LOW and T_HIGH to suit your own box.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Libraries: OneWire, DallasTemperature, Adafruit SSD1306 and Adafruit GFX.
#include <OneWire.h>
#include <DallasTemperature.h>
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>

const uint8_t FAN_PIN = 3;               // PWM pin to the MOSFET gate
const float T_LOW = 30.0;                // at or below this: slowest speed
const float T_HIGH = 55.0;               // at or above this: full speed
const uint8_t DUTY_MIN = 90;             // about 35 percent, so the fans never stall
const uint8_t DUTY_MAX = 255;

OneWire oneWire(2);
DallasTemperature probe(&oneWire);
Adafruit_SSD1306 oled(128, 64, &Wire, -1);

void setup() {
  pinMode(FAN_PIN, OUTPUT);
  analogWrite(FAN_PIN, DUTY_MAX);        // full speed until the first reading
  Serial.begin(9600);
  probe.begin();
  oled.begin(SSD1306_SWITCHCAPVCC, 0x3C);
}

void loop() {
  probe.requestTemperatures();
  float t = probe.getTempCByIndex(0);
  uint8_t duty;
  bool lost = (t == DEVICE_DISCONNECTED_C || t < -40);
  if (lost) {
    duty = DUTY_MAX;                     // fail safe: no reading means full cooling
  } else if (t <= T_LOW) {
    duty = DUTY_MIN;
  } else if (t >= T_HIGH) {
    duty = DUTY_MAX;
  } else {
    duty = DUTY_MIN + (uint8_t)((t - T_LOW) * (DUTY_MAX - DUTY_MIN) / (T_HIGH - T_LOW));
  }
  analogWrite(FAN_PIN, duty);

  int percent = duty * 100 / 255;
  oled.clearDisplay();
  oled.setTextColor(SSD1306_WHITE);
  oled.setTextSize(2);
  oled.setCursor(0, 0);
  if (lost) oled.print(F("NO PROBE")); else { oled.print(t, 1); oled.print(F(" C")); }
  oled.setCursor(0, 28);
  oled.print(F("Fans "));
  oled.print(percent);
  oled.print(F("%"));
  oled.fillRect(0, 54, map(percent, 0, 100, 0, 128), 8, SSD1306_WHITE);
  oled.display();

  Serial.print(F("Temp "));
  Serial.print(t, 1);
  Serial.print(F(" C, fans "));
  Serial.print(percent);
  Serial.println(F("%"));
  delay(1000);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

Temp 24.5 C, fans 35%

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Probe at room temperatureThe fans turn slowly at about 35 percent
Hold the probe in your handThe temperature climbs and the percentage rises
Dip the probe in warm waterFans reach 100 percent at 55 degrees
Unplug the probe wireNO PROBE shows and the fans run at full speed
Unplug USB and power up from the adapterThe fans stay off until the Nano has started

If it does not work

Fans stay at full speed

The probe reads -127, so check the 4.7 k resistor and the three probe wires.

Fans do not turn

Check the diode and the fan wires, and that the MOSFET legs are gate, drain, source from the left with the flat side facing you.

Nano resets when the fans start

Keep the 5 V converter separate from the fan wires and add a 100 uF capacitor across the Nano power.

Whining from the fans

PWM can make a hum on some fans, so raise DUTY_MIN or try a different T_LOW.

Screen blank

Check SDA and SCL and try address 0x3D.

Upload fails

Choose the Old Bootloader option for the Nano.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the PWM fan hub for a PC case?

Arduino Nano, 12 V DC fan 80 mm × 4, DS18B20 Temperature Sensor, Resistor 4.7 kΩ, MOSFET IRLZ44N, Resistor 220 Ω, Resistor 10 kΩ, Rectifier Diode 1N4007, SSD1306 OLED Display, 12 V 2 A DC adapter, DC barrel to screw terminal adapter (female), LM2596 Buck Module, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the PWM fan hub for a PC case take to build?

About 120 minutes for a beginner maker, in 8 steps.

How do I know the PWM fan hub for a PC case works?

Probe at room temperature: The fans turn slowly at about 35 percent. Hold the probe in your hand: The temperature climbs and the percentage rises. Dip the probe in warm water: Fans reach 100 percent at 55 degrees.

Fans stay at full speed: what should I check?

The probe reads -127, so check the 4.7 k resistor and the three probe wires.

Fans do not turn: what should I check?

Check the diode and the fan wires, and that the MOSFET legs are gate, drain, source from the left with the flat side facing you.

Nano resets when the fans start: what should I check?

Keep the 5 V converter separate from the fan wires and add a 100 uF capacitor across the Nano power.

Whining from the fans: what should I check?

PWM can make a hum on some fans, so raise DUTY_MIN or try a different T_LOW.