Projects / Pico W fridge temperature watch

Pico W fridge temperature watch

Intermediate2.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. PICODS18B2025.8°C

    Wire the probe

    Red to 3V3(OUT), black to GND, yellow to GP15.

  2. PICO

    Add the resistor

    4.7 kilo-ohms between the yellow wire and 3V3(OUT).

  3. PICO

    Edit the program

    Put your Wi-Fi name and password in the placeholders.

  4. PICO

    Run it

    The shell prints an address like http://192.168.1.50.

  5. PICO

    Open the address

    On a phone or computer on the same network.

  6. PICODS18B2025.9°C

    Put the probe in a glass of ice water

    It reads close to 0 degrees.

  7. PICO

    Place it in the fridge

    Feed the thin cable through the door seal, without pinching it.

In short

How do you build a pico W fridge temperature watch?

A Pico W reads a DS18B20 probe and serves the current, lowest and highest temperature on a local page, with a warning line if it stays above 8 degrees for an hour. You need Raspberry Pi Pico W, DS18B20 waterproof probe, Resistor 4.7 kΩ and Breadboard 830 Tie Points. It takes 7 steps and about 150 minutes.

Level
Intermediate
Time
About 150 min
Parts
4

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
DS18B20 red wire (VDD)Pico W 3V3(OUT) pin 36Power at 3.3 V
DS18B20 black wire (GND)Pico W GND pin 38Common ground
DS18B20 yellow wire (DATA)Pico W GP15 pin 20One-wire data
4.7 kilo-ohm resistorBetween DS18B20 DATA and 3V3(OUT)Pull-up for the data line

Code

The DS18B20 is a digital temperature probe that sends its reading over a single data wire, called one-wire, using a small protocol that MicroPython handles in its onewire and ds18x20 modules. The 4.7 kilo-ohm resistor holds the data line high between messages. The stainless-steel probe on a thin cable can be fed through the door seal of a fridge without cutting anything. The program reads the temperature every ten seconds, remembers the lowest and highest values, and starts a timer when the reading goes above 8 degrees, which is the usual upper limit for a domestic fridge. If it stays above for an hour it shows a red warning on the page. Put the probe in a small glass of water on a shelf so that it follows the temperature of the food rather than the quick changes of the air when the door opens. The page is for your home network only. A hobby monitor, not a food-safety instrument: follow official food-safety guidance for anything that matters.

import time
import network
import socket
import onewire
import ds18x20
from machine import Pin

SSID = "YOUR_WIFI_NAME"                             # placeholders: use your own network
PASSWORD = "YOUR_WIFI_PASSWORD"
LIMIT = 8.0                                         # degrees C
WARN_AFTER_MS = 3600000                             # one hour above the limit

ds = ds18x20.DS18X20(onewire.OneWire(Pin(15)))
roms = ds.scan()
if not roms:
    raise RuntimeError("No DS18B20 found, check the wiring and the 4.7k resistor")

wlan = network.WLAN(network.STA_IF)
wlan.active(True)
wlan.connect(SSID, PASSWORD)
for _ in range(30):
    if wlan.isconnected():
        break
    time.sleep(0.5)
if not wlan.isconnected():
    raise RuntimeError("Wi-Fi did not connect, check the name and password")
print("Open http://" + wlan.ifconfig()[0])

server = socket.socket()
server.bind(("0.0.0.0", 80))
server.listen(1)
server.settimeout(1)

current = None
lowest = None
highest = None
above_since = None
warning = False
last_read = time.ticks_add(time.ticks_ms(), -10000)

def update():
    global current, lowest, highest, above_since, warning
    ds.convert_temp()
    time.sleep_ms(800)
    current = ds.read_temp(roms[0])
    lowest = current if lowest is None else min(lowest, current)
    highest = current if highest is None else max(highest, current)
    if current > LIMIT:
        if above_since is None:
            above_since = time.ticks_ms()
        elif time.ticks_diff(time.ticks_ms(), above_since) >= WARN_AFTER_MS:
            warning = True
    else:
        above_since = None
        warning = False

while True:
    if time.ticks_diff(time.ticks_ms(), last_read) >= 10000:
        update()
        last_read = time.ticks_ms()
    try:
        client, addr = server.accept()
    except OSError:
        continue                                    # no visitor, go round again
    client.recv(1024)
    note = "<p style='color:red;font-size:1.5em'>Above " + str(LIMIT) + " C for over an hour</p>" if warning else "<p>Within the limit</p>"
    page = ("<!DOCTYPE html><html><head><meta charset='utf-8'>"
            "<meta name='viewport' content='width=device-width, initial-scale=1'>"
            "<meta http-equiv='refresh' content='30'><title>Fridge</title></head>"
            "<body style='font-family:sans-serif;text-align:center;margin-top:3em'>"
            "<h1>Fridge</h1><p style='font-size:3em'>%.1f &deg;C</p>"
            "<p>Lowest %.1f &deg;C, highest %.1f &deg;C since start</p>%s</body></html>"
            % (current, lowest, highest, note))
    client.send("HTTP/1.0 200 OK\r\nContent-Type: text/html\r\n\r\n")
    client.send(page)
    client.close()

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Probe in room airNear room temperature
Probe in ice waterClose to 0 degrees
Probe in a warm handRises towards 30 degrees
Fridge shelfBetween 2 and 8 degrees
Lowest and highestKeep the extremes since start

If it does not work

No DS18B20 found

Check the 4.7 kilo-ohm resistor between data and 3V3 and the three wires.

Reads 85.0 or -127

Check the power wire and the pull-up resistor.

Page does not open

Check the address from the shell and that the phone is on the same Wi-Fi.

Wi-Fi does not connect

Check the name and password, and that the network is 2.4 GHz.

Door does not seal

Use a thin, flat part of the cable and check the seal after fitting.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the pico W fridge temperature watch?

Raspberry Pi Pico W, DS18B20 waterproof probe, Resistor 4.7 kΩ and Breadboard 830 Tie Points.

How long does the pico W fridge temperature watch take to build?

About 150 minutes for a intermediate maker, in 7 steps.

How do I know the pico W fridge temperature watch works?

Probe in room air: Near room temperature. Probe in ice water: Close to 0 degrees. Probe in a warm hand: Rises towards 30 degrees.

No DS18B20 found: what should I check?

Check the 4.7 kilo-ohm resistor between data and 3V3 and the three wires.

Reads 85.0 or -127: what should I check?

Check the power wire and the pull-up resistor.

Page does not open: what should I check?

Check the address from the shell and that the phone is on the same Wi-Fi.

Wi-Fi does not connect: what should I check?

Check the name and password, and that the network is 2.4 GHz.