Projects / Pico temperature logger with a probe

Pico temperature logger with a probe

Intermediate2.3 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. PICODS18B2027.7°C

    Wire the probe

    Red to 3V3(OUT), black to GND, yellow to GP15.

  2. PICO

    Add the pull-up

    4.7 kilo-ohm from GP15 to 3V3(OUT).

  3. PICO

    Wire the display

    SDA to GP0, SCL to GP1, power at 3.3 V.

  4. PICO17.0 mASSD1306

    Install the ssd1306 module

    Using Thonny packages.

  5. PICO

    Save the program as main.py

    On the Pico.

  6. PICO

    Run it

    A temperature appears.

  7. PICODS18B2027.8°C

    Dip the probe in cold and warm water

    Watch the minimum and maximum.

In short

How do you build a pico temperature logger with a probe?

A Pico reads a DS18B20 probe with MicroPython and shows the value and the lowest and highest readings on an OLED. You need Raspberry Pi Pico H, DS18B20 waterproof probe, Resistor 4.7 kΩ, SSD1306 OLED Display and Breadboard 830 Tie Points. It takes 7 steps and about 140 minutes.

Level
Intermediate
Time
About 140 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
DS18B20 redPico 3V3(OUT) pin 36Power at 3.3 V
DS18B20 blackPico GND pin 38Ground
DS18B20 yellowPico GP15 pin 20One-wire data
4.7 kilo-ohm resistorBetween GP15 and 3V3(OUT)Pull-up for the data line
OLED VCC and GNDPico 3V3(OUT) and GNDPower at 3.3 V
OLED SDA and SCLPico GP0 pin 1 and GP1 pin 2I2C data and clock

Code

The DS18B20 is a digital probe that sends its reading as a number over one data wire, and MicroPython has built-in modules to talk to it. The data line must be pulled up to 3.3 V by a 4.7 kilo-ohm resistor, since the probe only pulls the line low. The program scans the bus for the probe address, then in a loop asks for a conversion, waits 750 milliseconds for it to finish and reads the result. The lowest and highest values since start are kept and shown, which is handy for a fridge, a room overnight or a cup of tea going cold. The values are also printed, so you can copy them from the Thonny shell into a spreadsheet. Readings are indicative only: a probe in air follows the temperature slowly, and its metal tip must touch whatever you are measuring. Do not use it for food safety or medical decisions.

import time
import onewire, ds18x20
from machine import Pin, I2C
from ssd1306 import SSD1306_I2C

i2c = I2C(0, sda=Pin(0), scl=Pin(1), freq=400000)
oled = SSD1306_I2C(128, 64, i2c)

ds = ds18x20.DS18X20(onewire.OneWire(Pin(15)))
roms = ds.scan()
if not roms:
    oled.text("No probe found", 0, 0)
    oled.show()
    raise SystemExit

lowest, highest = 1000.0, -1000.0

while True:
    ds.convert_temp()
    time.sleep_ms(750)                       # 12-bit conversion takes up to 750 ms
    t = ds.read_temp(roms[0])
    lowest = min(lowest, t)
    highest = max(highest, t)
    oled.fill(0)
    oled.text("DS18B20 logger", 0, 0)
    oled.text("Now: {:.1f} C".format(t), 0, 20)
    oled.text("Min: {:.1f} C".format(lowest), 0, 36)
    oled.text("Max: {:.1f} C".format(highest), 0, 48)
    oled.show()
    print("{:.2f}".format(t))                # also readable in the Thonny shell
    time.sleep(1)

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Probe in airRoom temperature that settles slowly
Probe in cold waterValue falls
Probe in warm waterValue rises
Min and maxTrack the lowest and highest values
Unplug the probe and restartNo probe found message

If it does not work

No probe found

Check the yellow wire on GP15 and the 4.7 kilo-ohm pull-up.

Reads 85 degrees

The probe has just powered up, wait for the next reading.

ImportError for ssd1306

Install the micropython-ssd1306 package.

Blank screen

Check the OLED address 0x3C and the GP0 and GP1 wires.

Program does not start on power-up

Save it on the Pico as main.py.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the pico temperature logger with a probe?

Raspberry Pi Pico H, DS18B20 waterproof probe, Resistor 4.7 kΩ, SSD1306 OLED Display and Breadboard 830 Tie Points.

How long does the pico temperature logger with a probe take to build?

About 140 minutes for a intermediate maker, in 7 steps.

How do I know the pico temperature logger with a probe works?

Probe in air: Room temperature that settles slowly. Probe in cold water: Value falls. Probe in warm water: Value rises.

No probe found: what should I check?

Check the yellow wire on GP15 and the 4.7 kilo-ohm pull-up.

Reads 85 degrees: what should I check?

The probe has just powered up, wait for the next reading.

ImportError for ssd1306: what should I check?

Install the micropython-ssd1306 package.

Blank screen: what should I check?

Check the OLED address 0x3C and the GP0 and GP1 wires.