Projects / Pico precision NTC thermometer

Pico precision NTC thermometer

Intermediate2.7 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. PICO

    Wire the converter

    VDD to 3V3(OUT), GND to GND, SDA to GP0, SCL to GP1, ADDR to GND.

  2. PICO26.0°C

    Build the divider

    10 kilo-ohm from 3V3(OUT) to A0, thermistor from A0 to GND.

  3. PICO

    Reference the supply

    A1 to the 3V3(OUT) rail.

  4. PICO14.8 mASSD1306

    Wire the OLED

    3V3(OUT), GND, SDA, SCL on the same bus.

  5. PICO14.8 mASSD1306

    Install the ssd1306 module

    Using Thonny packages.

  6. PICO

    Run the program

    The temperature appears.

  7. PICO26.1°C

    Pinch the thermistor

    The temperature rises.

In short

How do you build a pico precision NTC thermometer?

A Pico reads a 10 kilo-ohm NTC thermistor through an ADS1115 16-bit converter and shows a temperature to one decimal place on an OLED. You need Raspberry Pi Pico H, ADS1115 16-bit ADC module, NTC thermistor 10 kΩ (B3950), Resistor 10 kΩ, SSD1306 OLED Display and Breadboard 830 Tie Points. It takes 7 steps and about 160 minutes.

Level
Intermediate
Time
About 160 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
ADS1115 VDD and OLED VCCPico 3V3(OUT) pin 36Power at 3.3 V
ADS1115 GND and OLED GNDPico GND pin 38Common ground
ADS1115 SDA and OLED SDAPico GP0 pin 1Shared I2C data
ADS1115 SCL and OLED SCLPico GP1 pin 2Shared I2C clock
ADS1115 ADDRPico GNDSets the address 0x48
10 kilo-ohm resistor3V3(OUT) rail to ADS1115 A0Top of the divider
NTC thermistorADS1115 A0 to GNDBottom of the divider
ADS1115 A13V3(OUT) railReference of the actual supply voltage

Code

A thermistor is a resistor whose resistance falls as it warms. A 10 kilo-ohm NTC has exactly that resistance at 25 degrees and about 3.5 kilo-ohms at 45. To measure it you put it in a voltage divider with a fixed resistor and measure the voltage in the middle. The ADS1115 is a 16-bit converter, much finer than the Pico's own, and it has a built-in amplifier. A neat trick here is to read two channels: A0 gives the divider voltage and A1 reads the supply rail itself, so the ratio of the two gives the divider ratio without depending on the exact supply voltage. From the ratio the program works out the thermistor's resistance, and the beta equation turns resistance into temperature. Beta is a number from the data sheet, 3950 for this part, and the equation is accurate to about half a degree around room temperature. The averaging of eight readings steadies the last digit. The fixed resistor's tolerance is the main remaining error.

import time
import math
from machine import Pin, I2C
from ssd1306 import SSD1306_I2C

i2c = I2C(0, sda=Pin(0), scl=Pin(1), freq=400000)
oled = SSD1306_I2C(128, 64, i2c)
ADS = 0x48

R_FIXED = 10000.0
R0 = 10000.0                                        # thermistor resistance at 25 C
BETA = 3950.0
T0 = 298.15                                         # 25 C in kelvin

def read_channel(config_high):
    i2c.writeto(ADS, bytes([0x01, config_high, 0x83]))   # single shot, 128 samples a second, +-4.096 V
    time.sleep_ms(10)
    data = i2c.readfrom_mem(ADS, 0x00, 2)
    raw = (data[0] << 8) | data[1]
    if raw & 0x8000:
        raw -= 65536
    return raw * 4.096 / 32768

def temperature():
    v0 = 0.0
    v1 = 0.0
    for _ in range(8):
        v0 += read_channel(0xC3)                    # A0 against ground
        v1 += read_channel(0xD3)                    # A1 against ground, the supply voltage
    ratio = v0 / v1                                 # the ratio does not depend on the exact 3.3 V
    r_ntc = R_FIXED * ratio / (1 - ratio)
    inv_t = 1 / T0 + math.log(r_ntc / R0) / BETA
    return 1 / inv_t - 273.15

while True:
    t = temperature()
    oled.fill(0)
    oled.text("NTC thermometer", 0, 0)
    oled.text("%.1f C" % t, 0, 24)
    oled.show()
    time.sleep_ms(500)

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Room airAbout room temperature
Pinch the thermistorRises by several degrees
Blow on itFalls a little
Warm water, in a plastic bagReads the water temperature
Ice water, in a bagClose to 0 degrees

If it does not work

Reads nonsense

Check the divider is wired with the thermistor on the ground side.

OSError on the converter

Check the address 0x48 and the I2C wires.

Reads high or low by a few degrees

Check the fixed resistor value, and the thermistor's beta number.

Reading jumps

Keep the wires short and the thermistor still.

Display blank

Check the OLED address 0x3C.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the pico precision NTC thermometer?

Raspberry Pi Pico H, ADS1115 16-bit ADC module, NTC thermistor 10 kΩ (B3950), Resistor 10 kΩ, SSD1306 OLED Display and Breadboard 830 Tie Points.

How long does the pico precision NTC thermometer take to build?

About 160 minutes for a intermediate maker, in 7 steps.

How do I know the pico precision NTC thermometer works?

Room air: About room temperature. Pinch the thermistor: Rises by several degrees. Blow on it: Falls a little.

Reads nonsense: what should I check?

Check the divider is wired with the thermistor on the ground side.

OSError on the converter: what should I check?

Check the address 0x48 and the I2C wires.

Reads high or low by a few degrees: what should I check?

Check the fixed resistor value, and the thermistor's beta number.

Reading jumps: what should I check?

Keep the wires short and the thermistor still.