Projects / Pico eight-knob bank on one analog pin

Pico eight-knob bank on one analog pin

Intermediate2.5 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. PICO

    Power the chip

    Pin 16 to 3V3(OUT), pins 7, 8 and 6 to GND.

  2. PICO

    Wire the select lines

    S0, S1, S2 to GP2, GP3, GP4.

  3. PICO

    Wire the output

    Pin 3 to GP26.

  4. PICO

    Wire four knobs

    Wipers to Y0 to Y3, outer legs to 3V3(OUT) and GND.

  5. PICO

    Tie the unused inputs

    Y4 to Y7 to GND.

  6. PICO

    Save the program as main.py

    On the Pico.

  7. PICO

    Run it

    Four percentages print.

  8. PICO

    Turn one knob

    Only its number changes.

In short

How do you build a pico eight-knob bank on one analog pin?

A Pico reads four knobs through a 74HC4051 analog multiplexer on a single ADC pin, the start of a small mixer or controller. You need Raspberry Pi Pico H, 74HC4051 8-channel analog multiplexer, Potentiometer 10 kΩ × 4 and Breadboard 830 Tie Points. It takes 8 steps and about 150 minutes.

Level
Intermediate
Time
About 150 min
Parts
4

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
74HC4051 VCC (pin 16)Pico 3V3(OUT) pin 36Power at 3.3 V
74HC4051 GND (pin 8) and VEE (pin 7)Pico GNDVEE must go to ground for 0 to 3.3 V signals
74HC4051 E (pin 6)Pico GNDAlways enabled
74HC4051 S0, S1, S2 (pins 11, 10, 9)Pico GP2, GP3, GP4Channel select
74HC4051 Z (pin 3)Pico GP26 pin 31 (ADC0)Shared output to the ADC
Knob wipers74HC4051 Y0 to Y3 (pins 13, 14, 15, 12)One knob per channel, outer legs to 3V3(OUT) and GND
Unused inputs Y4 to Y7 (pins 1, 5, 2, 4)Pico GNDAvoid floating inputs

Code

A multiplexer is a switch that connects one of several inputs to one output, chosen by a binary number on its select pins. The 74HC4051 has eight inputs, three select pins and one common pin, which goes to a single ADC pin of the Pico. Counting from 0 to 3 on the three select lines connects each knob in turn, and the program reads and prints all four, so one ADC pin does the job of four. The chip needs its VEE pin tied to ground when the signals run from 0 to 3.3 V, and it should run from 3.3 V so the signals never go above the Pico limit. After switching, a short pause and one throwaway read let the sample capacitor settle, otherwise a reading carries a little of the previous knob. The inputs you do not use are tied to ground so they do not float. Each channel can only be read one at a time, which is fine for knobs.

import time
from machine import Pin, ADC

selects = [Pin(2, Pin.OUT), Pin(3, Pin.OUT), Pin(4, Pin.OUT)]   # S0, S1, S2
adc = ADC(26)
CHANNELS = 4

def read_channel(ch):
    for bit in range(3):
        selects[bit].value((ch >> bit) & 1)      # set the three select lines
    time.sleep_us(20)                            # let the analog switch settle
    adc.read_u16()                               # dummy read to flush the old value
    total = 0
    for _ in range(8):
        total += adc.read_u16()
    return total // 8

while True:
    values = []
    for ch in range(CHANNELS):
        values.append(read_channel(ch) * 100 // 65535)   # percent of full scale
    print("Knobs:", values)
    time.sleep_ms(100)

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
All knobs at zeroFour zeros
Turn knob 1Only the first value changes
Turn knob 4Only the last value changes
Full turnAbout 100
ReadingsSteady with little crosstalk

If it does not work

Values leak between knobs

Increase the settle time or read twice before averaging.

All values the same

Check the select lines and the common pin.

Values stuck at zero

Check VCC, E to GND and VEE to GND.

Noisy readings

Add 100 nanofarad from GP26 to GND.

Chip warm

Check VEE and VCC are not swapped.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the pico eight-knob bank on one analog pin?

Raspberry Pi Pico H, 74HC4051 8-channel analog multiplexer, Potentiometer 10 kΩ × 4 and Breadboard 830 Tie Points.

How long does the pico eight-knob bank on one analog pin take to build?

About 150 minutes for a intermediate maker, in 8 steps.

How do I know the pico eight-knob bank on one analog pin works?

All knobs at zero: Four zeros. Turn knob 1: Only the first value changes. Turn knob 4: Only the last value changes.

Values leak between knobs: what should I check?

Increase the settle time or read twice before averaging.

All values the same: what should I check?

Check the select lines and the common pin.

Values stuck at zero: what should I check?

Check VCC, E to GND and VEE to GND.

Noisy readings: what should I check?

Add 100 nanofarad from GP26 to GND.