Projects / Pi AirPlay and Spotify receiver

Pi AirPlay and Spotify receiver

Beginner1.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. Pi ZeroSANDISRASPBERR

    Flash the card

    Use Raspberry Pi Imager with your Wi-Fi and SSH.

  2. Pi Zero

    Wire the DAC

    Five wires and the clock pin to ground.

  3. Pi Zero

    Enable the overlay

    Add the dtoverlay line and reboot.

  4. Pi ZeroSANDIS

    Check the card

    aplay -l lists the DAC.

  5. Pi Zero

    Install AirPlay

    shairport-sync, then name it.

  6. Pi Zero

    Install Spotify Connect

    Follow Raspotify's instructions.

  7. Pi Zero

    Plug in the amplifier

    Play from a phone.

In short

How do you build a pi AirPlay and Spotify receiver?

A Pi Zero 2 W with an I2S DAC turns old speakers into a wireless receiver for AirPlay and Spotify Connect. You need Raspberry Pi Zero 2 W, SanDisk microSD card 32 GB (A1, Class 10), Raspberry Pi 15 W USB-C power supply, PCM5102 I2S DAC module, Audio jack 3.5 mm (PCB, stereo) and Jumper wires female to female (40 pcs). It takes 7 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
PCM5102 VINPi pin 1 (3.3 V)Power
PCM5102 GNDPi pin 6 (GND)Ground
PCM5102 BCKPi pin 12 (GPIO18)I2S bit clock
PCM5102 LRCKPi pin 35 (GPIO19)I2S word select
PCM5102 DINPi pin 40 (GPIO21)I2S data
PCM5102 SCKGNDUse the internal clock (many boards have a solder pad for this)
PCM5102 line outStereo jack or amplifier inputAudio out

Code

The Pi Zero 2 W has no good analogue output, so a PCM5102 DAC board on the I2S pins gives clean line-level sound for an amplifier or powered speakers. Many PCM5102 boards need the SCK pin tied to ground (or a solder pad bridged) so the chip makes its own clock; read your board's notes. Install Raspotify from its own project page and read what any installer script does before running it. Spotify Connect needs a Premium account. Use a good 5 V supply of 2.5 A for the Zero (a micro-USB one), as weak supplies cause crackles and resets. Do not put the Pi on an open network where strangers can stream to it; AirPlay has no password unless you set one in the shairport-sync file. Do not store your Wi-Fi password in files you share. Line-level output should go to an amplifier input, never directly to a speaker.

# Pi AirPlay and Spotify receiver. Run these on the Pi over SSH. Not an Arduino sketch.
# 1. Flash Raspberry Pi OS Lite with Raspberry Pi Imager. In its settings add your own Wi-Fi details and enable SSH.
# 2. Enable the DAC: add this line at the end of /boot/firmware/config.txt (older images use /boot/config.txt)
#      dtoverlay=hifiberry-dac
#    and comment out "dtparam=audio=on", then reboot.
sudo nano /boot/firmware/config.txt
sudo reboot
# 3. Check the DAC appears as a sound card.
aplay -l
# 4. Install the AirPlay receiver.
sudo apt update
sudo apt install -y shairport-sync
# Edit /etc/shairport-sync.conf. In the general section set the name, and in the alsa section the device:
#   general = { name = "Workshop speakers"; };
#   alsa = { output_device = "hw:0"; };
sudo nano /etc/shairport-sync.conf
sudo systemctl enable --now shairport-sync
# 5. Spotify Connect: install Raspotify by following its project instructions
#    (it is a Spotify Connect client for the Pi, needs a Spotify Premium account on your phone).
# 6. Both services start at boot. Check them.
systemctl status shairport-sync
systemctl status raspotify

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
PhoneThe speaker name appears in AirPlay and Spotify
Play a songClean sound from the speakers
Reboot the PiBoth services return by themselves
Walk away from the routerGaps, then it recovers

If it does not work

aplay shows no card

Check the overlay line and the wiring.

No sound

Check output_device in the shairport-sync config.

Crackles

Use a better power supply and a short audio cable.

Not visible on the phone

Phone and Pi must be on the same network.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the pi AirPlay and Spotify receiver?

Raspberry Pi Zero 2 W, SanDisk microSD card 32 GB (A1, Class 10), Raspberry Pi 15 W USB-C power supply, PCM5102 I2S DAC module, Audio jack 3.5 mm (PCB, stereo) and Jumper wires female to female (40 pcs). Raspberry Pi 15 W USB-C power supply: Use a micro-USB 5 V 2.5 A supply for the Zero.

How long does the pi AirPlay and Spotify receiver take to build?

About 90 minutes for a beginner maker, in 7 steps.

How do I know the pi AirPlay and Spotify receiver works?

Phone: The speaker name appears in AirPlay and Spotify. Play a song: Clean sound from the speakers. Reboot the Pi: Both services return by themselves.

aplay shows no card: what should I check?

Check the overlay line and the wiring.

No sound: what should I check?

Check output_device in the shairport-sync config.

Crackles: what should I check?

Use a better power supply and a short audio cable.

Not visible on the phone: what should I check?

Phone and Pi must be on the same network.