Projects / RC phase-shift oscillator

RC phase-shift oscillator

Intermediate1.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. BC547

    Bias the transistor

    Collector near half supply.

  2. Add the RC ladder

    Three stages from collector to base.

  3. Listen with the piezo

    A steady tone appears.

  4. Measure the frequency

    Compare with the formula.

  5. Change a capacitor

    See the tone move.

  6. Break one stage

    Watch it stop.

  7. Write up the result

    Link gain and phase to oscillation.

In short

How do you build an RC phase-shift oscillator?

Three RC stages and one transistor make an oscillator, showing the Barkhausen criterion. You need BC547 NPN transistor, Piezo disc buzzer element, Ceramic capacitor 10 nF × 3, Resistor 10 kΩ × 4, Resistor 4.7 kΩ, Resistor 100 kΩ, Electrolytic capacitor 10 µF, Breadboard 830 Tie Points, 9 V battery and 9 V battery snap with DC jack. It takes 7 steps and about 90 minutes.

Level
Intermediate
Time
About 90 min
Parts
10
See the electronics first. This build uses transistor switch. Try a transistor switch in the circuit builder and watch the voltages and currents before you wire it.

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
9 V battery plusSupply railPower
4.7 kΩ resistorRail to BC547 collectorCollector load
100 kΩ resistorRail to baseBias
Three 10 nF capacitors with 10 kΩ resistorsCollector to base in an RC ladder180 degree phase shift
EmitterGroundGround
Piezo elementCollector to ground through 10 µFHear the tone

No code needed

An oscillator needs two things: the signal fed back must come back in step with the input, and the gain must be big enough to replace losses. One transistor stage flips the signal by 180 degrees, and three RC sections each add about 60 degrees, so the signal returns in step at one frequency, roughly 1 over 2π times root six times RC, around 650 Hz for 10 kΩ and 10 nF. The gain must be about 29 or more, which a transistor with a decent load can give. Compare the measured frequency with the formula, then change one capacitor and watch the oscillation stop or the tone move. A 9 V battery is fine; do not use a mains supply for experiments.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Power onTone starts within a second
FrequencyNear the formula value
Capacitor doubledPitch falls
One stage removedNo oscillation

If it does not work

No tone

Raise the gain by changing the bias or collector load.

Distorted tone

Reduce the gain slightly.

Wrong pitch

Check the values of resistors and capacitors.

Weak tone

Use a piezo with a series capacitor.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the RC phase-shift oscillator?

BC547 NPN transistor, Piezo disc buzzer element, Ceramic capacitor 10 nF × 3, Resistor 10 kΩ × 4, Resistor 4.7 kΩ, Resistor 100 kΩ, Electrolytic capacitor 10 µF, Breadboard 830 Tie Points, 9 V battery and 9 V battery snap with DC jack. Piezo disc buzzer element: Lets you hear the tone.

How long does the RC phase-shift oscillator take to build?

About 90 minutes for a intermediate maker, in 7 steps.

How do I know the RC phase-shift oscillator works?

Power on: Tone starts within a second. Frequency: Near the formula value. Capacitor doubled: Pitch falls.

No tone: what should I check?

Raise the gain by changing the bias or collector load.

Distorted tone: what should I check?

Reduce the gain slightly.

Wrong pitch: what should I check?

Check the values of resistors and capacitors.

Weak tone: what should I check?

Use a piezo with a series capacitor.