Projects / Onion storage ventilation controller

Onion storage ventilation controller

Intermediate2 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANOSHT31AHT2027.9°CPCF8574

    Test both sensors

    Print inside and outside readings with an I2C scan first.

  2. NANOSHT31AHT2027.9°C

    Check the addresses

    SHT31 at 0x44 and AHT20 at 0x38.

  3. NANOSHT31AHT20ON28.0°C

    Wire the fan and relay

    Test the fan from a simple sketch.

  4. NANOSHT31AHT2028.0°C

    Upload

    Breathe on the inside sensor to raise its humidity.

  5. NANOSHT31AHT2028.0°C

    Compare absolute humidity

    Watch the two values on the serial monitor.

  6. NANO

    Check the rule

    The fan should start only when outside is drier.

  7. NANOSHT31AHT2028.0°C

    Install

    Place the sensors and fans in the shed; log fan hours each day.

In short

How do you build an onion storage ventilation controller?

Fans in an onion shed run when outside air is drier than inside air, which keeps stored onions from rotting. You need Arduino Nano, SHT31 temperature and humidity sensor, AHT20 temperature and humidity sensor, Relay Module 5V, 12 V DC fan 80 mm, 12 V 2 A DC adapter and 16x2 LCD with I2C backpack (PCF8574). It takes 7 steps and about 120 minutes.

Level
Intermediate
Time
About 120 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
SHT31 (inside) VCC and GNDNano 5V and GNDPower, check your module accepts 5 V
SHT31 SDA and SCLNano A4 and A5I2C address 0x44
AHT20 (outside) VCC and GNDNano 5V and GNDPower
AHT20 SDA and SCLNano A4 and A5I2C address 0x38, keep the cable short
LCD I2C SDA and SCLNano A4 and A5Display
Relay module VCC, GNDNano 5V and GNDCoil power
Relay module INNano D7Fan control
12 V adapter +Relay COMFan supply
Relay NOFan +Switched positive
Fan - and adapter -JoinedReturn

Code

Comparing relative humidity alone can mislead, because cold air at 80 percent holds far less water than warm air at 80 percent. The code converts both readings to absolute humidity, grams of water per cubic metre, and runs the fan only when the outside air holds noticeably less moisture than the shed air, so ventilation dries the onions instead of wetting them. The fan stops when the difference falls or the shed is dry enough. Keep the outside sensor in shade and rain protection, and because both sensors share an I2C bus, keep the cable to the outside one short, or use a second Nano. Onions store best dry and cool, with good air movement; follow local advice for target conditions. Arduino IDE, board "Arduino Nano" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones).

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Libraries: Adafruit SHT31, Adafruit AHTX0, LiquidCrystal_I2C.
#include <Wire.h>
#include <Adafruit_SHT31.h>
#include <Adafruit_AHTX0.h>
#include <LiquidCrystal_I2C.h>
#include <math.h>

Adafruit_SHT31 inside;
Adafruit_AHTX0 outside;
LiquidCrystal_I2C lcd(0x27, 16, 2);
const byte RELAY = 7;
const bool ACTIVE_LOW = true;
bool fanOn = false;
unsigned long fanStart = 0, fanTotal = 0;

// Absolute humidity in grams of water per cubic metre of air
float absHum(float tC, float rh) {
  return 6.112 * exp(17.67 * tC / (tC + 243.5)) * rh * 2.1674 / (273.15 + tC);
}

void fan(bool on) {
  if (on && !fanOn) fanStart = millis();
  if (!on && fanOn) fanTotal += millis() - fanStart;
  fanOn = on;
  digitalWrite(RELAY, (on == ACTIVE_LOW) ? LOW : HIGH);
}

void setup() {
  Serial.begin(9600);
  pinMode(RELAY, OUTPUT); fan(false);
  inside.begin(0x44);
  outside.begin();
  lcd.init(); lcd.backlight();
}

void loop() {
  float ti = inside.readTemperature(), hi = inside.readHumidity();
  sensors_event_t h, t;
  outside.getEvent(&h, &t);
  float to = t.temperature, ho = h.relative_humidity;
  if (!isnan(ti) && !isnan(hi)) {
    float ahIn = absHum(ti, hi), ahOut = absHum(to, ho);
    float diff = ahIn - ahOut;                      // positive: outside air is drier
    if (!fanOn && diff > 2.0 && hi > 65) fan(true);  // outside air can carry moisture away
    if (fanOn && (diff < 0.5 || hi < 60)) fan(false);
    lcd.setCursor(0, 0);
    lcd.print("In "); lcd.print(hi, 0); lcd.print("% Out "); lcd.print(ho, 0); lcd.print("%  ");
    lcd.setCursor(0, 1);
    lcd.print(fanOn ? "Fan ON  " : "Fan off ");
    lcd.print((fanTotal + (fanOn ? millis() - fanStart : 0)) / 3600000.0, 1); lcd.print(" h   ");
    Serial.print(ahIn); Serial.print(","); Serial.println(ahOut);
  }
  delay(5000);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

0.00,0.00

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Outside drier than insideFan on
Outside humidFan stays off
Inside dry enoughFan off
Fan hoursIncrease on dry days

If it does not work

Outside sensor not found

Check its address and wiring; long cables cause errors.

Fan never starts

Check the thresholds and the relay logic.

Both readings the same

Check the sensors are not side by side.

LCD blank

Try address 0x3F.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the onion storage ventilation controller?

Arduino Nano, SHT31 temperature and humidity sensor, AHT20 temperature and humidity sensor, Relay Module 5V, 12 V DC fan 80 mm, 12 V 2 A DC adapter and 16x2 LCD with I2C backpack (PCF8574).

How long does the onion storage ventilation controller take to build?

About 120 minutes for a intermediate maker, in 7 steps.

How do I know the onion storage ventilation controller works?

Outside drier than inside: Fan on. Outside humid: Fan stays off. Inside dry enough: Fan off.

Outside sensor not found: what should I check?

Check its address and wiring; long cables cause errors.

Fan never starts: what should I check?

Check the thresholds and the relay logic.

Both readings the same: what should I check?

Check the sensors are not side by side.

LCD blank: what should I check?

Try address 0x3F.