Projects / 1-Wire sensor bus

1-Wire sensor bus

Beginner45 minGuided buildReviewed

Build it step by step

0 of 6 done
  1. NANODS18B2023.0°C

    Wire one sensor

    Connect a single DS18B20 with the pull-up and read it.

  2. NANO

    Add the others

    Connect all four data pins to D2 and see the count change to four.

  3. NANO

    Note the IDs

    Copy each ROM ID from the Serial Monitor.

  4. NANO

    Label them

    Warm one sensor in your fingers to see which ID rises, then stick a label on it.

  5. NANO

    Test a long cable

    Extend the data wire with twisted cable and see how far it works.

  6. NANO

    Use the IDs

    Change the sketch to print a name next to each ID.

In short

How do you build a 1-Wire sensor bus?

Many DS18B20 sensors share one data wire, each found by its unique ID. You need Arduino Nano, DS18B20 Temperature Sensor × 4, Resistor 4.7 kΩ, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 6 steps and about 45 minutes.

Level
Beginner
Time
About 45 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
All DS18B20 pin 1 (GND)Nano GNDGround
All DS18B20 pin 3 (VDD)Nano 5VPower
All DS18B20 pin 2 (DQ)Nano D2One shared data line
4.7 kΩ resistorD2 and 5VSingle pull-up for the whole bus

Code

Arduino IDE, board "Arduino Nano" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones). Install "OneWire" and "DallasTemperature". The DS18B20 TO-92 pins, flat face towards you, are GND, DQ, VDD from the left. Wire with the power off, because a reversed sensor gets hot very quickly.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <OneWire.h>
#include <DallasTemperature.h>

OneWire oneWire(2);
DallasTemperature sensors(&oneWire);

void printAddress(DeviceAddress a) {
  for (byte i = 0; i < 8; i++) { if (a[i] < 16) Serial.print('0'); Serial.print(a[i], HEX); }
}

void setup() {
  Serial.begin(9600);
  sensors.begin();
  Serial.print("Sensors found: "); Serial.println(sensors.getDeviceCount());
}

void loop() {
  sensors.requestTemperatures();
  for (byte i = 0; i < sensors.getDeviceCount(); i++) {
    DeviceAddress addr;
    if (sensors.getAddress(addr, i)) {
      Serial.print("Sensor "); Serial.print(i); Serial.print(" ID ");
      printAddress(addr);
      Serial.print("  "); Serial.print(sensors.getTempC(addr), 2); Serial.println(" C");
    }
  }
  Serial.println();
  delay(1000);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

Sensors found: 1
Sensor 0 ID 28FF641E0F16035C  24.50 C

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Four sensorsCount is four and each has its own ID
Warm one sensorOnly that sensor's reading rises
Unplug oneCount drops to three
Room temperatureAll four read within about 0.5 °C

If it does not work

Count is zero

Check the 4.7 kΩ pull-up between D2 and 5V.

Reads -127

Sensor lost power or the data wire is loose.

Reads 85

The sensor did not finish converting. Check power and wait before reading.

Sensor gets very hot

It was wired backwards. Disconnect, let it cool and check the pinout.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the 1-Wire sensor bus?

Arduino Nano, DS18B20 Temperature Sensor × 4, Resistor 4.7 kΩ, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the 1-Wire sensor bus take to build?

About 45 minutes for a beginner maker, in 6 steps.

How do I know the 1-Wire sensor bus works?

Four sensors: Count is four and each has its own ID. Warm one sensor: Only that sensor's reading rises. Unplug one: Count drops to three.

Count is zero: what should I check?

Check the 4.7 kΩ pull-up between D2 and 5V.

Reads -127: what should I check?

Sensor lost power or the data wire is loose.

Reads 85: what should I check?

The sensor did not finish converting. Check power and wait before reading.

Sensor gets very hot: what should I check?

It was wired backwards. Disconnect, let it cool and check the pinout.