Projects / Motor start-stop with relays

Motor start-stop with relays

Beginner1 hGuided buildReviewed

Build it step by step

0 of 6 done
  1. Draw the ladder

    Sketch the control rung with STOP in series, START in parallel with the hold-in contact, then the coil.

  2. ON

    Wire the coil

    Connect the relay coil with its flyback diode and test it with a temporary link.

  3. 12.7 mA

    Add the hold-in

    Wire contact set 1 across the START button.

  4. 12.7 mA

    Add the stop button

    Put the normally-closed stop button in series with the control supply.

  5. Wire the motor

    Feed the motor through contact set 2 with its own diode.

  6. ON

    Test the sequence

    Press start and release, then stop, and watch the motor and relay.

In short

How do you build a motor start-stop with relays?

A classic hold-in relay circuit starts a 12 V motor with one button and stops it with another. You need Relay 24 V DPDT (MY2N), Push button 16 mm metal (momentary, LED) × 2, Johnson geared motor 300 RPM 12 V, 12 V 2 A DC adapter, Rectifier Diode 1N4007 × 2 and Terminal block 12-way (barrier strip). It takes 6 steps and about 60 minutes.

Level
Beginner
Time
About 60 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
12 V adapter +Stop button (normally closed)Supply through the stop button
Stop button other sideStart button (normally open) and relay contact set 1 NOControl node
Start button other side and contact set 1 COMJoined to the relay coil + terminalHold-in path
Relay coil - terminal12 V adapter -Return
1N4007 diodeAcross the relay coil, cathode to coil +Flyback diode
12 V adapter + (before the stop button)Relay contact set 2 COMMotor supply
Relay contact set 2 NOMotor +Switched motor feed
Motor -12 V adapter -Return
1N4007 diodeAcross the motor, cathode to motor +Motor flyback diode

No code needed

No code, only relay logic. Use a relay with a 12 V coil (a 24 V coil relay will not pull in properly on 12 V) and a stop button with a normally-closed contact: pressing it breaks the control supply. When START is pressed, the coil energises and contact set 1 closes across the START button, so the coil stays powered after release (the hold-in or seal-in). Contact set 2 feeds the motor. Pressing STOP drops the coil and the motor stops. Keep the motor current under the relay and adapter rating (a stalled motor can draw several amps). Any mains control must be wired by a qualified electrician; this build stays at 12 V.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Press STARTRelay clicks in and the motor runs
Release STARTMotor keeps running
Press STOPRelay drops and the motor stops
Press START without releaseSame as above

If it does not work

Relay drops when START is released

The hold-in contact is not wired across START.

Relay does not click

Check the coil voltage and the stop button type.

Motor does not run

Check contact set 2 wiring and the supply.

Relay buzzes

Voltage is too low. Use a proper 12 V adapter.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the motor start-stop with relays?

Relay 24 V DPDT (MY2N), Push button 16 mm metal (momentary, LED) × 2, Johnson geared motor 300 RPM 12 V, 12 V 2 A DC adapter, Rectifier Diode 1N4007 × 2 and Terminal block 12-way (barrier strip).

How long does the motor start-stop with relays take to build?

About 60 minutes for a beginner maker, in 6 steps.

How do I know the motor start-stop with relays works?

Press START: Relay clicks in and the motor runs. Release START: Motor keeps running. Press STOP: Relay drops and the motor stops.

Relay drops when START is released: what should I check?

The hold-in contact is not wired across START.

Relay does not click: what should I check?

Check the coil voltage and the stop button type.

Motor does not run: what should I check?

Check contact set 2 wiring and the supply.

Relay buzzes: what should I check?

Voltage is too low. Use a proper 12 V adapter.