Projects / Morse beacon with keying circuit

Morse beacon with keying circuit

Beginner45 minGuided buildReviewed

Build it step by step

0 of 6 done
  1. NANO

    Wire the sidetone

    Connect the passive buzzer to D9 and GND and upload the sketch.

  2. NANO

    Check the timing

    Listen at 12 WPM: a dash is three times a dot, and a letter gap is three dots.

  3. NANO

    Change the message

    Edit MESSAGE and WPM and upload again.

  4. NANOPC817

    Wire the optocoupler

    Add the 330 Ω resistor and PC817 as in the table, leaving the output side open.

  5. NANOPC817

    Check the LED

    A small LED in place of the optocoupler would flash in time with the buzzer.

  6. NANO

    Use the key line (licensed users)

    Connect pins 3 and 4 to the key jack of a rig you are licensed to use at low power into a dummy load first.

In short

How do you build a morse beacon with keying circuit?

An Arduino plays a repeating Morse message on a buzzer and can key an amateur radio's key jack through an optocoupler. You need Arduino Nano, Passive buzzer, Optocoupler PC817, Resistor 330 Ω, Resistor 1 kΩ and Breadboard 830 Tie Points. It takes 6 steps and about 45 minutes.

Level
Beginner
Time
About 45 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Nano D9Passive buzzer +Sidetone
Passive buzzer -Nano GNDReturn
Nano D8330 Ω resistor then PC817 pin 1 (anode)Drives the optocoupler LED
PC817 pin 2 (cathode)Nano GNDReturn
PC817 pin 4 (collector)Radio key jack tipIsolated key line (optional, licensed use only)
PC817 pin 3 (emitter)Radio key jack sleeveIsolated key line (optional, licensed use only)

Code

Arduino IDE, board "Arduino Nano" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones). Practise with the buzzer only. The key line is for connecting to the key jack of a radio whose owner holds an amateur licence, and you may only transmit with your own call sign within the rules of your country. The optocoupler only switches a key line of a few milliamps, never a transmitter's power.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

const byte KEY_LED = 8, BUZZER = 9;
const int WPM = 12;                                // words per minute
const unsigned int DOT = 1200 / WPM;               // dot length in ms
const char MESSAGE[] = "VVV DE YOURCALL";          // replace with your own message

const char* TABLE[] = {
  ".-", "-...", "-.-.", "-..", ".", "..-.", "--.", "....", "..", ".---", "-.-", ".-..", "--",
  "-.", "---", ".--.", "--.-", ".-.", "...", "-", "..-", "...-", ".--", "-..-", "-.--", "--.."
};
const char* DIGITS[] = { "-----", ".----", "..---", "...--", "....-", ".....", "-....", "--...", "---..", "----." };

void key(bool on) {
  digitalWrite(KEY_LED, on);
  if (on) tone(BUZZER, 600); else noTone(BUZZER);
}

void sendSymbol(char c) {
  key(true);  delay(c == '.' ? DOT : 3 * DOT);
  key(false); delay(DOT);
}

void sendChar(char ch) {
  if (ch == ' ') { delay(7 * DOT); return; }
  const char* code = 0;
  if (ch >= 'A' && ch <= 'Z') code = TABLE[ch - 'A'];
  else if (ch >= '0' && ch <= '9') code = DIGITS[ch - '0'];
  if (!code) return;
  for (const char* p = code; *p; p++) sendSymbol(*p);
  delay(2 * DOT);                                  // 3 dots between letters in total
}

void setup() {
  pinMode(KEY_LED, OUTPUT);
}

void loop() {
  for (const char* p = MESSAGE; *p; p++) sendChar(*p);
  delay(5000);                                     // pause between repeats
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Upload with VVV DE messageBuzzer plays the Morse
WPM set to 20Faster code
WPM set to 5Slow practice code
Pins 3 and 4 measured with a meterShort circuit while the buzzer sounds, open between

If it does not work

Buzzer plays a steady tone

A passive buzzer needs tone(), check D9 and that noTone is called.

No keying on the optocoupler

Check the LED side polarity and the 330 Ω resistor.

Letters run together

Check the 2-dot delay after each letter.

Radio never keys

Check the key jack polarity and that the radio uses a simple closing-to-ground key line.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the morse beacon with keying circuit?

Arduino Nano, Passive buzzer, Optocoupler PC817, Resistor 330 Ω, Resistor 1 kΩ and Breadboard 830 Tie Points.

How long does the morse beacon with keying circuit take to build?

About 45 minutes for a beginner maker, in 6 steps.

How do I know the morse beacon with keying circuit works?

Upload with VVV DE message: Buzzer plays the Morse. WPM set to 20: Faster code. WPM set to 5: Slow practice code.

Buzzer plays a steady tone: what should I check?

A passive buzzer needs tone(), check D9 and that noTone is called.

No keying on the optocoupler: what should I check?

Check the LED side polarity and the 330 Ω resistor.

Letters run together: what should I check?

Check the 2-dot delay after each letter.

Radio never keys: what should I check?

Check the key jack polarity and that the radio uses a simple closing-to-ground key line.