Projects / USB MIDI drum pad controller

USB MIDI drum pad controller

Intermediate3 hGuided buildReviewed

Build it step by step

0 of 6 done
  1. ARDUINO

    Wire one pad

    Connect a piezo, 1 MΩ resistor and zener to A0 and print the readings while tapping.

  2. ARDUINO

    Set the threshold

    Choose THRESHOLD just above the noise when untouched.

  3. ARDUINO

    Add MIDI

    Upload the sketch and check the Leonardo appears as a MIDI device on your computer.

  4. ARDUINO

    Add the other pads

    Repeat the wiring for A1 to A3.

  5. ARDUINO

    Add the knobs

    Wire the four potentiometers to the knob inputs.

  6. ARDUINO

    Map in your DAW

    Assign CC 20 to 23 to effects such as filter or reverb.

In short

How do you build an USB MIDI drum pad controller?

An Arduino Leonardo shows up as a USB MIDI device, with piezo pads for drums and knobs for effects. You need Arduino Leonardo, Piezo disc buzzer element × 4, Resistor 1 MΩ × 4, Zener diode 5.1 V (1N4733A) × 4, Potentiometer 10 kΩ × 4 and USB A to micro-USB cable (data). It takes 6 steps and about 180 minutes.

Level
Intermediate
Time
About 180 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Each piezo disc (4 pads)Leonardo A0, A1, A2, A3 and GNDSignal and ground
1 MΩ resistor across each piezoPiezo signal and GNDBleeds the charge away
5.1 V zener across each piezoCathode (band) to the piezo signal, anode to GNDProtects the input from hit spikes
Potentiometer 1 outer pins, wiper5V and GND, wiper to A4Knob 1
Potentiometer 2 outer pins, wiper5V and GND, wiper to A5Knob 2
Potentiometer 3 outer pins, wiper5V and GND, wiper to D4 (analog A6)Knob 3
Potentiometer 4 outer pins, wiper5V and GND, wiper to D6 (analog A7)Knob 4
USB cableLeonardo USB portPower and MIDI to the computer

Code

Arduino IDE, board "Arduino Leonardo" (its ATmega32u4 can act as a USB MIDI device; an Uno or Nano cannot). Install the "MIDIUSB" library. Use a DAW or a free drum plugin and select the Leonardo as a MIDI input. Mount each piezo disc under a firm foam pad on a rigid plate so a hit makes a sharp spike. A zener across each piezo and a 1 MΩ resistor keep the analog pin safe from the brief high voltage of a hard hit.

Runs on a virtual Arduino Leonardo in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <MIDIUSB.h>

const byte PADS[4] = { A0, A1, A2, A3 };
const byte NOTES[4] = { 36, 38, 42, 45 };          // kick, snare, closed hi-hat, tom
const byte KNOBS[4] = { A4, A5, A6, A7 };          // analog inputs on D4 and D6 for the last two
const byte CCS[4] = { 20, 21, 22, 23 };
const int THRESHOLD = 40;                          // ignore noise below this reading
const unsigned long LOCKOUT = 60;                  // ms, stops a hit retriggering
unsigned long lastHit[4] = { 0, 0, 0, 0 };
int lastKnob[4] = { -10, -10, -10, -10 };

void noteOn(byte note, byte vel)  { midiEventPacket_t e = { 0x09, 0x90, note, vel }; MidiUSB.sendMIDI(e); MidiUSB.flush(); }
void noteOff(byte note)           { midiEventPacket_t e = { 0x08, 0x80, note, 0 };   MidiUSB.sendMIDI(e); MidiUSB.flush(); }
void control(byte cc, byte value) { midiEventPacket_t e = { 0x0B, 0xB0, cc, value }; MidiUSB.sendMIDI(e); MidiUSB.flush(); }

void setup() {}

void loop() {
  for (byte i = 0; i < 4; i++) {
    int v = analogRead(PADS[i]);
    if (v > THRESHOLD && millis() - lastHit[i] > LOCKOUT) {
      int peak = v;
      unsigned long t = micros();
      while (micros() - t < 4000) { int r = analogRead(PADS[i]); if (r > peak) peak = r; }   // catch the peak of the hit
      byte velocity = constrain(map(peak, THRESHOLD, 900, 20, 127), 1, 127);
      noteOn(NOTES[i], velocity);
      delay(30);
      noteOff(NOTES[i]);
      lastHit[i] = millis();
    }
  }
  for (byte k = 0; k < 4; k++) {
    int v = analogRead(KNOBS[k]) / 8;                // 0 to 127
    if (abs(v - lastKnob[k]) > 1) { control(CCS[k], v); lastKnob[k] = v; }
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Tap a pad softlyQuiet drum note
Tap hardLouder note (higher velocity)
No hitNo notes sent
Turn a knobA control change message appears in the DAW

If it does not work

No device appears

You need a board with native USB, such as the Leonardo.

Double triggers

Raise the lockout time or threshold.

Pads always on

The zener or resistor is missing, or the threshold is too low.

Crosstalk between pads

Isolate the pads with foam and raise the threshold.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the USB MIDI drum pad controller?

Arduino Leonardo, Piezo disc buzzer element × 4, Resistor 1 MΩ × 4, Zener diode 5.1 V (1N4733A) × 4, Potentiometer 10 kΩ × 4 and USB A to micro-USB cable (data).

How long does the USB MIDI drum pad controller take to build?

About 180 minutes for a intermediate maker, in 6 steps.

How do I know the USB MIDI drum pad controller works?

Tap a pad softly: Quiet drum note. Tap hard: Louder note (higher velocity). No hit: No notes sent.

No device appears: what should I check?

You need a board with native USB, such as the Leonardo.

Double triggers: what should I check?

Raise the lockout time or threshold.

Pads always on: what should I check?

The zener or resistor is missing, or the threshold is too low.

Crosstalk between pads: what should I check?

Isolate the pads with foam and raise the threshold.