Joule thief LED from a dead cell
Build it step by step
0 of 7 doneWind the toroid
Two strands together, about 10 turns.
Make the centre tap
Join the end of one to the start of the other.
Wire the transistor
Collector, base through 1 k, emitter.
Add the LED
Across the collector winding.
Fit a used AA cell
The LED lights.
Check the supply voltage
Meter across the cell.
Find the lowest voltage
Note when it stops.
How do you build a joule thief LED from a dead cell?
One transistor and a hand-wound toroid light a white LED from an AA cell too weak for a torch. You need BC547 NPN transistor, Resistor 1 kΩ, Toroid inductor 100 µH 3 A, LED 5 mm white, AA alkaline battery and Battery holder 2 × AA. It takes 7 steps and about 45 minutes.
- Level
- Beginner
- Time
- About 45 min
- Parts
- 6
Parts list
- SemiconductorsBuy
- PassivesBuyResistor 1 kΩ × 1
- PassivesBuyRewind with two windings
- OptoelectronicsBuyLED 5 mm white × 1
- BatteriesBuy
- PowerBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| Cell plus | Centre tap (end of winding 1 joined to start of winding 2) | Battery positive |
| Winding 1 free end | BC547 collector | Main switching winding |
| Winding 2 free end | 1 k resistor, then BC547 base | Feedback winding |
| BC547 emitter | Cell minus | Battery negative |
| White LED anode | BC547 collector | LED lights from the voltage spike |
| White LED cathode | Cell plus (centre tap) | Across winding 1 |
No code needed
A joule thief is a one-transistor oscillator that makes a low voltage useful. The transistor switches on, current builds in the first winding, and the second winding feeds back to keep the transistor on until the core is full. Then the transistor turns off, the collapsing field makes a short spike much higher than the cell voltage, and that spike lights the LED. This repeats tens of thousands of times a second, so the LED looks steadily lit. Wind two strands of thin enamelled wire together about ten turns each on a ferrite toroid, then join the end of one to the start of the other for the centre tap. If the LED never lights, the windings are in the wrong sense: swap the two ends of one winding. Use a 1.5 V cell that is nearly flat; the circuit works down to about 0.7 V. Use only alkaline or other cells that are not swollen or leaking, and recycle dead cells. The spike can be several volts higher than the cell, so this is safe, but do not touch the transistor, which gets warm after long use. There is no code for this build.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Fresh cell | LED bright |
| Cell at 1.0 V | LED still glowing |
| Swap one winding's ends | Starts or stops oscillating |
| Meter across the LED | Reads a steady, low average voltage |
If it does not work
No light
Swap the ends of one winding.
Very dim
Try a smaller base resistor, such as 470 ohms.
Transistor hot
Use a larger base resistor or fewer turns.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the joule thief LED from a dead cell?
BC547 NPN transistor, Resistor 1 kΩ, Toroid inductor 100 µH 3 A, LED 5 mm white, AA alkaline battery and Battery holder 2 × AA. Toroid inductor 100 µH 3 A: Rewind with two windings.
How long does the joule thief LED from a dead cell take to build?
About 45 minutes for a beginner maker, in 7 steps.
How do I know the joule thief LED from a dead cell works?
Fresh cell: LED bright. Cell at 1.0 V: LED still glowing. Swap one winding's ends: Starts or stops oscillating.
No light: what should I check?
Swap the ends of one winding.
Very dim: what should I check?
Try a smaller base resistor, such as 470 ohms.
Transistor hot: what should I check?
Use a larger base resistor or fewer turns.
