Helping hands with USB light and fan
Build it step by step
0 of 7 doneMount the fan
On one arm, blowing across the work.
Mount the LED
On the other arm with paste.
Add the resistor
10 Ω, 1 W, in series.
Wire to the USB breakout
Check polarity.
Add a switch
In the 5 V line.
Tidy the cables
Clips and heat shrink.
Test for an hour
Check the LED and resistor stay warm, not hot.
How do you build a helping hands with USB light and fan?
Upgrade helping hands with a USB-powered LED and a small fan to blow away fumes. You need Helping hands with magnifier, 5 V DC fan 40 mm, High-power LED 1 W white (star), Resistor 10 Ω, USB-A female breakout and USB A to micro-USB cable (data). It takes 7 steps and about 45 minutes.
- Level
- Beginner
- Time
- About 45 min
- Parts
- 6
Parts list
- Tools & InstrumentsBuy
- Motors & ActuatorsBuy5 V DC fan 40 mm × 1
- OptoelectronicsBuy
- PassivesBuyResistor 10 Ω × 1
- ConnectorsBuy
- Cables & WiresBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| USB breakout 5V | Fan plus, and 10 Ω resistor to LED anode | Two branches |
| USB breakout GND | Fan minus and LED cathode | Common return |
| LED star | Bolted to an aluminium arm | Heat sink |
| Switch | In the 5 V line | Optional on-off |
| USB cable | A 5 V 1 A or larger charger | Power |
No code needed
This build has no code. A 1 W white LED star drops about 3 V, so from 5 V it needs a series resistor: a 10 Ω resistor gives about 200 mA, which lights it brightly and stays well inside the LED's 1 W rating. That resistor dissipates about 0.4 W, so use a 1 W resistor, not a small quarter-watt one. Bolt the star to an aluminium arm with thermal paste so it can lose heat; a 1 W LED with no heat sink can burn out or become too hot to touch. The 40 mm fan draws about 100 mA, which together with the LED stays within one amp from a USB charger. Point the fan across the work, not at your face, so it draws fumes away to the side, and keep fingers out of the blades; this is a convenience, not a replacement for proper ventilation. Cover every joint with heat shrink, and do not use an unmarked charger of unknown quality.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| LED | Bright and steady |
| Fan | Moves air across the work |
| Resistor | Warm but not too hot to touch |
| Charger | No overheating |
If it does not work
LED dim
Check the resistor value.
LED very hot
Improve the heat sinking.
Fan slow
Check the supply can give 1 A.
Flicker
Check the connections.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the helping hands with USB light and fan?
Helping hands with magnifier, 5 V DC fan 40 mm, High-power LED 1 W white (star), Resistor 10 Ω, USB-A female breakout and USB A to micro-USB cable (data).
How long does the helping hands with USB light and fan take to build?
About 45 minutes for a beginner maker, in 7 steps.
How do I know the helping hands with USB light and fan works?
LED: Bright and steady. Fan: Moves air across the work. Resistor: Warm but not too hot to touch.
LED dim: what should I check?
Check the resistor value.
LED very hot: what should I check?
Improve the heat sinking.
Fan slow: what should I check?
Check the supply can give 1 A.
Flicker: what should I check?
Check the connections.
