Projects / FM radio with station names (RDS)

FM radio with station names (RDS)

Intermediate2.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. ESP32

    Wire the tuner

    Reset, I2C and power.

  2. ESP32

    Tune a station

    Hear it in headphones.

  3. ESP3210.8 mASSD1306

    Add the OLED

    Show the frequency.

  4. ESP32

    Add the encoder

    Move 0.1 MHz at a time.

  5. ESP32

    Add seek

    Press to find the next station.

  6. ESP32

    Read the RDS

    Show the station name.

  7. ESP32

    Make a station list

    Save favourites.

In short

How do you build an FM radio with station names (RDS)?

A Si4703 tuner decodes RDS, so the radio shows the station name and song text on an OLED. You need ESP32 DevKit V1, Si4703 FM tuner with RDS, SSD1306 OLED Display, Rotary encoder module (KY-040), Headphone jack module 3.5 mm, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 150 minutes.

Level
Intermediate
Time
About 150 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Si4703 SDIOESP32 GPIO21I2C data (also the mode select at reset)
Si4703 SCLKESP32 GPIO22I2C clock
Si4703 RSTESP32 GPIO4Reset
Si4703 VIO and 3.3VESP32 3V3Power
Si4703 GNDESP32 GNDGround
Si4703 headphone out (L, R, GND)Headphone jack moduleAudio and antenna (the cable is the aerial)
OLED SDA and SCLESP32 GPIO21 and GPIO22Shared I2C bus
Encoder CLK, DT, SWESP32 GPIO32, GPIO33, GPIO25Tuning and seek

Code

FM broadcasts carry a tiny data stream called RDS alongside the music at a very low rate, which includes the station name. The Si4703 chip receives and decodes it, so the radio can show a name instead of just a number. The headphone cable is the aerial, so keep it plugged in and stretched out, and expect better reception near a window. Station names arrive in pieces about once every few seconds, so the display fills in after tuning; weak stations may never show one. The chip must be reset with its data line held low, which the library handles through the reset and data pins you give it, so keep those wires as shown. The library reads the station name; scrolling song text needs a library that assembles radiotext, which you can add later. Keep the volume modest in headphones, and remember that some countries have few RDS stations. Arduino IDE with the ESP32 boards package 2.0.x, board "ESP32 Dev Module".

Runs on a virtual ESP32 Dev Module in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// FM radio with RDS station names. Libraries: SparkFun Si4703 (SparkFunSi4703.h), Adafruit SSD1306, Adafruit GFX. Board: ESP32 Dev Module.
// Turn the encoder to move 0.1 MHz at a time, press it to seek up to the next station. The station name appears when the RDS data arrives.
#include <Wire.h>
#include <SparkFunSi4703.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
const int RESET_PIN = 4, SDIO_PIN = 21, SCLK_PIN = 22, STC_PIN = 5;   // STC_PIN: the library wants a spare pin, leave it unwired
Si4703_Breakout radio(RESET_PIN, SDIO_PIN, SCLK_PIN, STC_PIN);
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
const int CLK_PIN = 32, DT_PIN = 33, SW_PIN = 25;
int channel = 947;                          // 94.7 MHz, written as 947
int volume = 6;                             // 0 to 15
char station[10] = "";
volatile int delta = 0;
void IRAM_ATTR isr() { delta += (digitalRead(DT_PIN) != digitalRead(CLK_PIN)) ? 1 : -1; }
void show() {
  oled.clearDisplay(); oled.setTextSize(2); oled.setCursor(0, 0);
  oled.print(channel / 10); oled.print('.'); oled.print(channel % 10); oled.print(" MHz");
  oled.setTextSize(1); oled.setCursor(0, 30); oled.print(station[0] ? station : "(no RDS yet)");
  oled.setCursor(0, 50); oled.print("Volume "); oled.print(volume);
  oled.display();
}
void setup() {
  pinMode(CLK_PIN, INPUT_PULLUP); pinMode(DT_PIN, INPUT_PULLUP); pinMode(SW_PIN, INPUT_PULLUP);
  attachInterrupt(digitalPinToInterrupt(CLK_PIN), isr, FALLING);
  radio.powerOn();
  radio.setVolume(volume);
  radio.setChannel(channel);
  oled.begin(SSD1306_SWITCHCAPVCC, 0x3C);
  oled.setTextColor(SSD1306_WHITE);
  show();
}
void loop() {
  noInterrupts(); int d = delta; delta = 0; interrupts();
  if (d != 0) { channel = constrain(channel + d, 875, 1080); radio.setChannel(channel); station[0] = 0; show(); }
  if (!digitalRead(SW_PIN)) { channel = radio.seekUp(); station[0] = 0; show(); delay(300); }
  char buf[10] = "";
  radio.readRDS(buf, 800);                                          // wait up to 0.8 s for the station name
  if (buf[0] && strcmp(buf, station) != 0) { strncpy(station, buf, 9); station[9] = 0; show(); }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Power onPlays the set frequency
Turn the encoderFrequency changes
Press to seekJumps to the next station
Strong stationName appears within a few seconds

If it does not work

No sound

Check the headphone wiring and volume.

No RDS

Station may not send it; try a strong one.

Chip not found

Check the reset wiring before power-up.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the FM radio with station names (RDS)?

ESP32 DevKit V1, Si4703 FM tuner with RDS, SSD1306 OLED Display, Rotary encoder module (KY-040), Headphone jack module 3.5 mm, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the FM radio with station names (RDS) take to build?

About 150 minutes for a intermediate maker, in 7 steps.

How do I know the FM radio with station names (RDS) works?

Power on: Plays the set frequency. Turn the encoder: Frequency changes. Press to seek: Jumps to the next station.

No sound: what should I check?

Check the headphone wiring and volume.

No RDS: what should I check?

Station may not send it; try a strong one.

Chip not found: what should I check?

Check the reset wiring before power-up.