Projects / Programmable bench supply with DPS5005

Programmable bench supply with DPS5005

Beginner1.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. 12

    Choose the adapter

    19 to 24 V for full range.

  2. DCBANANA

    Mark the case

    Cut the jack, sockets and window.

  3. BANANA

    Fix the module

    Insulated standoffs.

  4. Wire the input

    Fuse, then module.

  5. BANANA

    Wire the outputs

    Red and black sockets.

  6. Test with a meter

    Set 5 V, 12 V.

  7. Save presets

    M1 for 3.3 V, M2 for 5 V.

In short

How do you build a programmable bench supply with DPS5005?

Fit a DPS5005 programmable supply module in a case with a laptop adapter for an accurate lab supply. You need Adjustable bench power supply module (DPS5005), 12 V 2 A DC adapter, DC power jack 5.5 x 2.1 mm (panel), Banana plug and socket 4 mm × 2 and ABS project box (100 × 60 × 25 mm). It takes 7 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Laptop adapterPanel DC jackSealed, ready-made mains adapter: never open it
Panel DC jackInline fuse, then DPS5005 input plus and minusUse short, thick wires and the right polarity
DPS5005 output plusRed banana socketOutput
DPS5005 output minusBlack banana socketOutput
CaseInsulated standoffs for the moduleNothing metal touching the board

No code needed

The DPS5005 is a ready-made module that turns a DC input into a steady, adjustable output, with a display and buttons to set the voltage and a current limit. Putting it in a case with a laptop adapter makes a bench supply that is safe to use because all the mains-side parts stay inside a sealed, certified adapter: you never touch mains wiring. The module's output can be no higher than its input, so a 19 to 24 V adapter gives the full range, while a 12 V adapter limits it to about 11 V. Set the current limit before you connect anything, since that limit is what protects a circuit and your wires when something goes wrong. Fit an inline fuse on the input, use thick wire for the high-current path, fix the module on insulated standoffs, and leave vents for the fan. Do not use it to charge lithium batteries without a proper charger, and never leave it running unattended with a load. Check the polarity of the adapter plug before you connect it, since the module can be damaged by reverse input.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Power onDisplay shows the set voltage
Output on with no loadMeter matches the display
Short the output briefly through a 10 ohm resistor at 100 mA limitLimit mode lights
FanRuns with load, air clear

If it does not work

Output too low

Check the input voltage and the current limit.

Module gets hot

Add vents and lower the load.

Display dead

Check input polarity and the fuse.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the programmable bench supply with DPS5005?

Adjustable bench power supply module (DPS5005), 12 V 2 A DC adapter, DC power jack 5.5 x 2.1 mm (panel), Banana plug and socket 4 mm × 2 and ABS project box (100 × 60 × 25 mm). 12 V 2 A DC adapter: Use a 19 to 24 V laptop adapter for full range.

How long does the programmable bench supply with DPS5005 take to build?

About 90 minutes for a beginner maker, in 7 steps.

How do I know the programmable bench supply with DPS5005 works?

Power on: Display shows the set voltage. Output on with no load: Meter matches the display. Short the output briefly through a 10 ohm resistor at 100 mA limit: Limit mode lights.

Output too low: what should I check?

Check the input voltage and the current limit.

Module gets hot: what should I check?

Add vents and lower the load.

Display dead: what should I check?

Check input polarity and the fuse.