Projects / Bench tool charging dock

Bench tool charging dock

Beginner1 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. Choose the supply

    12 V, 5 A for full output.

  2. Check each module's output

    5.0 V with a meter.

  3. USBUSBUSB

    Wire the USB ports

    A and C.

  4. Add the fuse and LED

    On the input.

  5. ABS

    Fit in the box

    Vents and labels.

  6. Test a device on each port

    Phone and multimeter.

  7. Test them together

    Watch the temperature.

In short

How do you build a bench tool charging dock?

A dock with USB-C and USB-A outputs from one 12 V supply charges multimeters, phones and tools. You need 12 V 2 A DC adapter, 5 V 3 A USB buck module (12/24 V to USB) × 2, USB-A female breakout × 2, USB-C Breakout Board and ABS project box (100 × 60 × 25 mm). It takes 7 steps and about 60 minutes.

Level
Beginner
Time
About 60 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
12 V supplyBoth USB buck modules IN+ and IN-Power in (add a fuse)
Buck module 1 USB outputUSB-A breakout 1Port 1
Buck module 2 USB outputUSB-A breakout 2 and the USB-C breakoutPorts 2 and 3
Power LEDAcross the 12 V input with its resistorShows the dock is on

No code needed

A bench is full of things that charge from USB: a multimeter, a phone, a headlamp, a soldering iron. One 12 V supply feeding two buck modules gives you several ports in one tidy box. A buck module lowers 12 V to a steady 5 V, and each one here can give up to 3 A, but remember the supply has to cover them: a 12 V 2 A adapter gives only 24 W in total, so two modules at full load would overload it. Choose a 12 V 5 A supply for the full output, and fit a fuse on the input. Check each output with a multimeter before plugging anything in, and label the ports. Some phones will not charge from a plain USB-C breakout unless it carries the small resistors that mark it as a 5 V source, so check your breakout and test with a spare device. Keep the box ventilated, since the modules warm up. Never charge lithium tools unattended on a flammable surface. There is no code for this build.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Each port5 V with no load
Phone chargingCurrent shown and steady
All ports usedSupply and modules stay warm, not hot
FuseFitted on the 12 V input

If it does not work

Phone does not charge on C

The breakout lacks the source marking.

Dock shuts down

The supply is too small.

Modules hot

Add vents and spread the loads.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the bench tool charging dock?

12 V 2 A DC adapter, 5 V 3 A USB buck module (12/24 V to USB) × 2, USB-A female breakout × 2, USB-C Breakout Board and ABS project box (100 × 60 × 25 mm). 12 V 2 A DC adapter: Use a 12 V 5 A supply for full output.

How long does the bench tool charging dock take to build?

About 60 minutes for a beginner maker, in 7 steps.

How do I know the bench tool charging dock works?

Each port: 5 V with no load. Phone charging: Current shown and steady. All ports used: Supply and modules stay warm, not hot.

Phone does not charge on C: what should I check?

The breakout lacks the source marking.

Dock shuts down: what should I check?

The supply is too small.

Modules hot: what should I check?

Add vents and spread the loads.