Projects / Cloud cover detector with an IR thermometer

Cloud cover detector with an IR thermometer

Intermediate1.3 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANO

    Test the sensor

    Print object and ambient temperature.

  2. NANO

    Point it at a wall

    Both numbers are close.

  3. NANO

    Point it at the sky

    The sky reading drops.

  4. NANO

    Add the difference

    Air minus sky.

  5. NANO

    Add the words

    Clear, Partly cloudy, Overcast.

  6. NANO

    Fit a tube

    Block side views with a short black tube.

  7. NANO

    Compare

    Look at the real sky and adjust.

In short

How do you build a cloud cover detector with an IR thermometer?

An MLX90614 pointed at the sky compares sky temperature with air temperature: a very cold sky means clear, a warm sky means cloud. You need Arduino Nano, MLX90614 infrared thermometer and SSD1306 OLED Display. It takes 7 steps and about 75 minutes.

Level
Intermediate
Time
About 75 min
Parts
3

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
MLX90614 VCC and GNDNano 5V and GNDPower (use the 5 V version of the module, or 3V3 for a 3.3 V one)
MLX90614 SDANano A4I2C data
MLX90614 SCLNano A5I2C clock
OLED VCC, GND, SDA, SCLNano 5V, GND, A4, A5Shares the I2C bus
USB or adapterNanoPower

Code

The infrared sensor measures the temperature of whatever it points at. A clear sky is very cold in the infrared, often 20 °C or more below the air temperature, while cloud bases radiate heat back and read close to the air. Point the sensor straight up through a small tube so that it sees only the sky and not roofs or trees. Thresholds depend on humidity, altitude and the sensor's field of view, so treat the words as a guide and adjust the two numbers after comparing with what you see overhead. Keep the sensor out of rain and direct sun, which can damage it, and cover the end with a thin infrared-transparent window (such as a sliver of polyethylene film) in a weatherproof box. It is a hobby indicator that is useful for choosing a night for stargazing or checking the night radiation that causes frost, not a replacement for a forecast. Arduino IDE, board "Arduino Nano" (try the Old Bootloader option if the upload fails).

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Cloud cover detector. Libraries: Adafruit MLX90614, Adafruit SSD1306, Adafruit GFX. Board: Arduino Nano.
#include <Wire.h>
#include <Adafruit_MLX90614.h>
#include <Adafruit_SSD1306.h>

Adafruit_MLX90614 mlx; Adafruit_SSD1306 oled(128, 64, &Wire, -1);

void setup() {
  mlx.begin();
  oled.begin(SSD1306_SWITCHCAPVCC, 0x3C); oled.setTextColor(SSD1306_WHITE);
}

void loop() {
  float sky = 0, air = 0;
  for (int i = 0; i < 20; i++) { sky += mlx.readObjectTempC(); air += mlx.readAmbientTempC(); delay(50); }
  sky /= 20; air /= 20;
  float diff = air - sky;                                   // a clear sky is much colder than the air near the ground
  const char* sky_text = "Overcast";
  if (diff > 25) sky_text = "Clear";
  else if (diff > 12) sky_text = "Partly cloudy";
  oled.clearDisplay();
  oled.setTextSize(1); oled.setCursor(0, 0); oled.print("Sky "); oled.print(sky, 1); oled.print("  Air "); oled.print(air, 1);
  oled.setCursor(0, 14); oled.print("Difference "); oled.print(diff, 1); oled.print(" C");
  oled.setTextSize(2); oled.setCursor(0, 36); oled.print(sky_text);
  oled.display();
  delay(2000);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Clear nightDifference above 25 and Clear
Thick cloudDifference under 12 and Overcast
Pointed at a wallDifference near zero
Rain on the windowKeep it dry

If it does not work

Always reads Overcast

Check the sensor sees the sky, not a roof.

Reads strange values

Check the I2C address and the module voltage.

Noisy

Average more readings.

Window blocks the view

Use thin polyethylene film.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the cloud cover detector with an IR thermometer?

Arduino Nano, MLX90614 infrared thermometer and SSD1306 OLED Display.

How long does the cloud cover detector with an IR thermometer take to build?

About 75 minutes for a intermediate maker, in 7 steps.

How do I know the cloud cover detector with an IR thermometer works?

Clear night: Difference above 25 and Clear. Thick cloud: Difference under 12 and Overcast. Pointed at a wall: Difference near zero.

Always reads Overcast: what should I check?

Check the sensor sees the sky, not a roof.

Reads strange values: what should I check?

Check the I2C address and the module voltage.

Noisy: what should I check?

Average more readings.

Window blocks the view: what should I check?

Use thin polyethylene film.