Projects / Hoop shot counter

Hoop shot counter

Beginner1.2 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. NANO12:45

    Install the TM1637Display library

    From the Library Manager.

  2. NANO

    Wire the sensor

    OUT to D2, 5V and GND.

  3. NANO

    Wire the display and buzzer

    Display on D5 and D6, buzzer on D8.

  4. NANO

    Wire the reset button

    D3 and GND.

  5. NANO

    Upload the sketch

    The display shows 0.

  6. NANO

    Pass a hand under the hoop

    The count goes to 1 with a beep.

  7. NANO

    Turn the sensor's knob

    Until it sees the ball only.

  8. NANO

    Press reset

    The count returns to zero.

In short

How do you build a hoop shot counter?

An infrared sensor under a toy basketball hoop spots each ball falling through the net, and a four-digit display counts the shots and plays a short beep. A button resets the count. Fun for a bedroom hoop, and a good sensor-and-display exercise. You need Arduino Nano, IR obstacle avoidance sensor module, TM1637 4-digit display, Passive buzzer, Tactile push button 6 mm, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 8 steps and about 70 minutes.

Level
Beginner
Time
About 70 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
IR sensor OUTNano D2Goes low when a ball passes in front of it
IR sensor VCC and GNDNano 5V and GNDSensor power
TM1637 CLK and DIONano D5 and D6Score display
TM1637 VCC and GNDNano 5V and GNDPower
Passive buzzer + and -Nano D8 and GNDShort beep
Reset buttonNano D3 and GNDSets the count to zero

Code

The sensor is mounted just under the hoop rim, looking across the opening, so a ball falling through the net breaks its beam for a moment. The sketch counts one shot each time the beam is broken, then waits until the beam has been clear for 80 milliseconds before it is ready again, and also ignores the sensor for 400 milliseconds after a count, so a ball bouncing in the net is not counted twice. Each count shows on the TM1637 display with a short beep, and the reset button sets it back to zero. Turn the sensor's small knob until it sees the ball but not the net, the wall behind or the room lights, and try shielding it from direct sunlight, which can fool this type of sensor. Install "TM1637Display" by Avishay Orpaz from the Library Manager. This is a toy hoop counter for fun. Use a light ball and a soft hoop that cannot hurt anyone, keep the wiring out of the way of the ball, and play where the ceiling and furniture are safe. Try a version that also counts misses by listening for the rebound.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Library: TM1637Display (by Avishay Orpaz).
#include <TM1637Display.h>

const uint8_t IR_PIN = 2;
const uint8_t BTN_RESET = 3;
const uint8_t CLK = 5;
const uint8_t DIO = 6;
const uint8_t BUZZ = 8;
const unsigned long LOCKOUT_MS = 400;     // ignore the sensor for a moment after each shot
const unsigned long CLEAR_MS = 80;        // the beam must be clear this long before the next count

TM1637Display display(CLK, DIO);

unsigned int shots = 0;
bool blocked = false;
unsigned long lastCount = 0;
unsigned long clearSince = 0;
bool armed = true;                         // ready for the next ball

void setup() {
  pinMode(IR_PIN, INPUT);
  pinMode(BTN_RESET, INPUT_PULLUP);
  pinMode(BUZZ, OUTPUT);
  Serial.begin(9600);
  display.setBrightness(3);
  display.showNumberDec(0, false);
}

void loop() {
  unsigned long now = millis();
  bool seen = (digitalRead(IR_PIN) == LOW);

  if (seen) {
    if (armed && now - lastCount > LOCKOUT_MS) {
      shots++;
      lastCount = now;
      armed = false;                       // wait for the beam to clear before counting again
      display.showNumberDec(shots, false);
      tone(BUZZ, 1500, 80);
      Serial.print(F("Basket! Total "));
      Serial.println(shots);
    }
    clearSince = now;
  } else if (!armed && now - clearSince > CLEAR_MS) {
    armed = true;
  }

  if (digitalRead(BTN_RESET) == LOW) {
    shots = 0;
    display.showNumberDec(0, false);
    tone(BUZZ, 600, 150);
    delay(300);
  }
  delay(5);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

Basket! Total 1

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Ball through the hoopCount goes up once with a beep
Ball bouncing in the netNot counted again
Reset buttonCount returns to zero
Serial monitorPrints the total
Strong sunlightMay need the sensor shaded

If it does not work

Counts without a ball

Turn the knob to reduce the range or shade the sensor.

Never counts

Turn the knob up and check OUT goes to D2.

Counts twice

Increase LOCKOUT_MS.

Display stays blank

Check CLK to D5 and DIO to D6.

Library not found

Install TM1637Display.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the hoop shot counter?

Arduino Nano, IR obstacle avoidance sensor module, TM1637 4-digit display, Passive buzzer, Tactile push button 6 mm, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the hoop shot counter take to build?

About 70 minutes for a beginner maker, in 8 steps.

How do I know the hoop shot counter works?

Ball through the hoop: Count goes up once with a beep. Ball bouncing in the net: Not counted again. Reset button: Count returns to zero.

Counts without a ball: what should I check?

Turn the knob to reduce the range or shade the sensor.

Never counts: what should I check?

Turn the knob up and check OUT goes to D2.

Counts twice: what should I check?

Increase LOCKOUT_MS.

Display stays blank: what should I check?

Check CLK to D5 and DIO to D6.