Workshop / Digital trainer

Digital trainer

A virtual 74xx IC trainer kit for your digital lab. Wire it, flip switches, watch the LEDs.

Flip SW0 and SW1 and watch LED L0: it is off only when both are 1.

Guided lab experiments

PowerLogic switchesPulse buttonsClockLED indicatorsDisplay 1 · lit when LOWDisplay 2 · BCD inU1 pin 14 (VCC) to +5 V. Tap to select.U1 pin 7 (GND) to GND. Tap to select.U1 pin 1 (1A) to SW0. Tap to select.U1 pin 2 (1B) to SW1. Tap to select.U1 pin 3 (1Y) to L0. Tap to select.GNDGND0Logic 0+5 V+5 V1Logic 10SW0SW00SW1SW10SW2SW20SW3SW30SW4SW40SW5SW50SW6SW60SW7SW7APulse AĀPulse A invertedBPulse BB̄Pulse B invertedCLKClockL0L0L1L1L2L2L3L3L4L4L5L5L6L6L7L7aD1abD1bcD1cdD1deD1efD1fgD1gAD2ABD2BCD2CDD2D7400U111AU1 pin 1 (1A)21BU1 pin 2 (1B)31YU1 pin 3 (1Y)42AU1 pin 4 (2A)52BU1 pin 5 (2B)62YU1 pin 6 (2Y)7GNDU1 pin 7 (GND)83YU1 pin 8 (3Y)93AU1 pin 9 (3A)103BU1 pin 10 (3B)114YU1 pin 11 (4Y)124AU1 pin 12 (4A)134BU1 pin 13 (4B)14VCCU1 pin 14 (VCC)U2empty socketU2U3empty socketU3U4empty socketU4U5empty socketU5U6empty socketU6U7empty socketU7U8empty socketU8
Tap two points to run a wire, or use Add a wire. Dots: dark LOW, bright HIGH, white not driven.
Clock comes out at CLK. Falling edge: 7473, 7476, 7490, 7493. Rising edge: 7474, 74194.

IC sockets

Power every IC: pin 14 (or 16) to +5 V, pin 7 (or 8) to GND. 7490, 7493 and 7483 differ; the pin names show where.

Add a wire

Wires on the board (5)

Wiring looks sensible: every chip you use has power and no input is open.

Readings table

Set the switches, then add a row: every wired switch and LED is recorded for your lab record.

Pinouts of the ICs on your board

U1 · 7400 Quad 2-input NAND
  1. 1 1A
  2. 2 1B
  3. 3 1Y
  4. 4 2A
  5. 5 2B
  6. 6 2Y
  7. 7 GND
  8. 8 3Y
  9. 9 3A
  10. 10 3B
  11. 11 4Y
  12. 12 4A
  13. 13 4B
  14. 14 VCC

Common questions

Is this a replacement for the digital trainer kit in my lab?

It is a way to practise. You wire real chip pinouts on a virtual trainer, so you arrive at the lab knowing the connections, but your college practical is still done on the kit your lab provides.

Which ICs are included?

7400, 7402, 7404, 7408, 7432, 7486, 7447, 7473, 7474, 7476, 7483, 7485, 7490, 7493, 74138, 74151, 74153 and 74194.

What mistakes does it catch?

A chip with no power, an open input (which reads HIGH on TTL), two outputs joined together and a short between +5 V and GND are all reported, as they would show up on a real kit.

Does it model gate delays?

No. Gates respond instantly, and flip-flops change on their clock edge. It teaches the logic, not timing.