Projects / Voltage-controlled oscillator with 4046

Voltage-controlled oscillator with 4046

Intermediate1.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. Place the chip on the breadboard

    Power and inhibit.

  2. Set R1 and C1

    10k and 10 nF.

  3. Feed pin 9 from the pot

    Add the second 10k.

  4. Listen

    Turn the pot slowly.

  5. Measure

    Frequency at five pot positions.

  6. Change the capacitor

    Note the new range.

  7. Add a second source

    Hear the modulation.

In short

How do you build a voltage-controlled oscillator with 4046?

The VCO in a CD4046 changes pitch with a control voltage, for synths and FM experiments. You need CD4046 phase-locked loop, Resistor 10 kΩ × 2, Potentiometer 10 kΩ, Ceramic capacitor 10 nF, LM386 amplifier module, Speaker 8 Ω 0.5 W, Breadboard 830 Tie Points, 9 V battery and 9 V battery snap with DC jack. It takes 7 steps and about 90 minutes.

Level
Intermediate
Time
About 90 min
Parts
9

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
CD4046 pin 16 (VDD)9 V battery plusPower
CD4046 pin 8 (VSS)9 V battery minusGround
CD4046 pin 5 (INH)GroundEnables the VCO
CD4046 pin 11 (R1)10k resistor to groundSets the pitch range
CD4046 pins 6 and 710 nF capacitor between themC1, sets the pitch range
CD4046 pin 12 (R2)Leave openLowest frequency is near zero
CD4046 pin 9 (VCO in)Pot wiperControl voltage
Pot endsSecond 10k to 9 V, other end to groundLimits the voltage range
CD4046 pins 3 and 14GroundUnused inputs parked
CD4046 pin 4 (VCO out)LM386 module inputSquare wave to the amplifier
LM386 module power9 V battery plus and minusSame battery, common ground
LM386 module outputSpeakerSound

No code needed

The CD4046 is a phase-locked loop chip, but its voltage-controlled oscillator can be used on its own: the voltage on pin 9 sets the pitch, a resistor and a capacitor choose the range, and a square wave appears on pin 4. Turning the pot gives a pitch sweep you can hear and measure. For a low, slow range use a bigger capacitor, and for a higher one use a smaller one. Try feeding pin 9 from a second oscillator through a series resistor and the pitch warbles, which is basic frequency modulation. It is a CMOS chip, so touch a grounded metal object before handling it, and never leave pin 9 floating, or the pitch will wander. It works from 9 V but is slower and less accurate than at higher supply; do not exceed 15 V. Keep the volume low, since a square wave is a harsh sound.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Pot at the bottomLow pitch
Pot at the topHigh pitch
Frequency against voltageRises smoothly
Chip power9 V on pin 16

If it does not work

No sound

Check pin 5 is grounded and the amplifier has power.

Pitch jumps

Check pin 9 is not floating.

Too high to hear

Use a larger capacitor.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the voltage-controlled oscillator with 4046?

CD4046 phase-locked loop, Resistor 10 kΩ × 2, Potentiometer 10 kΩ, Ceramic capacitor 10 nF, LM386 amplifier module, Speaker 8 Ω 0.5 W, Breadboard 830 Tie Points, 9 V battery and 9 V battery snap with DC jack.

How long does the voltage-controlled oscillator with 4046 take to build?

About 90 minutes for a intermediate maker, in 7 steps.

How do I know the voltage-controlled oscillator with 4046 works?

Pot at the bottom: Low pitch. Pot at the top: High pitch. Frequency against voltage: Rises smoothly.

No sound: what should I check?

Check pin 5 is grounded and the amplifier has power.

Pitch jumps: what should I check?

Check pin 9 is not floating.

Too high to hear: what should I check?

Use a larger capacitor.