Projects / Smart mirror with weather and calendar

Smart mirror with weather and calendar

Intermediate5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. Pi 4RASPBERRRASPBERR

    Flash the Pi

    Raspberry Pi OS with desktop, enable SSH.

  2. Pi 4

    Install MagicMirror

    Follow the project's steps.

  3. Pi 4

    Add clock, weather, calendar

    Edit config.js.

  4. Pi 4

    Test on a monitor

    Run it and check each module.

  5. Pi 4motion

    Add the PIR

    Make the screen sleep after 2 minutes.

  6. Pi 4

    Auto-start

    Use pm2 to launch at boot.

  7. Pi 4

    Build the frame

    Mirror in front, monitor behind, vents left open.

In short

How do you build a smart mirror with weather and calendar?

A Raspberry Pi behind a two-way mirror shows the time, weather and today's calendar using MagicMirror². You need Raspberry Pi 4 Model B (4 GB), Raspberry Pi 15 W USB-C power supply, SanDisk microSD card 32 GB (A1, Class 10), Raspberry Pi micro-HDMI to HDMI cable and PIR Motion Sensor HC-SR501. It takes 7 steps and about 300 minutes.

Level
Intermediate
Time
About 300 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
PIR VCCPi pin 2 (5 V)Power
PIR GNDPi pin 6 (GND)Ground
PIR OUTPi pin 11 (GPIO17)Motion signal (3.3 V output)
Pi micro-HDMIMonitor HDMIPicture
Pi USB-CRaspberry Pi power supplyPower
MonitorIts own power adapterMonitor power

Code

MagicMirror² is a free Node.js app that draws modules on a black background, which looks like floating text behind a two-way (one-way) mirror. Follow the project's own installation page for the right Node version, as it changes. The weather module can use Open-Meteo, which needs no key; the calendar needs the private iCal address of your calendar, which acts like a password, so keep it in your own config file and do not share it or put it in a repository. Rotate the screen to portrait in the Pi's display settings if you mount a monitor upright. Behind the mirror an old monitor gets warm, so leave ventilation gaps at the top and bottom of the frame and never cover the vents. The monitor's power adapter is a mains device: use the supplied, undamaged adapter and keep it out of the frame, with the lead through a proper strain relief. Fit the mirror securely so it cannot fall; acrylic mirror is safer than glass.

# Smart mirror setup. Run on the Pi (Raspberry Pi OS with desktop, 64-bit). Not an Arduino sketch.
# 1. Update and install Node.js as the MagicMirror project's instructions say (check their page for the version).
sudo apt update && sudo apt full-upgrade -y
# 2. Install MagicMirror from the official project.
git clone https://github.com/MagicMirrorOrg/MagicMirror
cd MagicMirror
npm run install-mcm
cp config/config.js.sample config/config.js
# 3. Edit config/config.js. Add or change modules, for example:
#    { module: "clock", position: "top_left" },
#    { module: "weather", position: "top_right",
#      config: { weatherProvider: "openmeteo", type: "current", lat: 12.97, lon: 77.59 } },
#    { module: "calendar", header: "Today", position: "top_left",
#      config: { calendars: [ { url: "YOUR_PRIVATE_ICAL_ADDRESS" } ] } },
nano config/config.js
# 4. Test it.
npm run start
# 5. Make it start at login with pm2 as the project's documentation describes.

# ---- Screen off when nobody is near: save as ~/pir_screen.py and run it at login ----
# from gpiozero import MotionSensor
# import subprocess, time
# pir = MotionSensor(17)
# off_after = 120
# last = time.time()
# while True:
#     if pir.motion_detected:
#         last = time.time()
#         subprocess.run(["vcgencmd", "display_power", "1"])
#     elif time.time() - last > off_after:
#         subprocess.run(["vcgencmd", "display_power", "0"])
#     time.sleep(1)
# (On recent Raspberry Pi OS with Wayland use wlr-randr to switch the output instead; check your image.)

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Power onMirror shows time and weather within a minute
Walk upScreen wakes
LeaveScreen turns off after 2 minutes
RebootThe mirror starts by itself

If it does not work

Blank screen

Check the HDMI cable and the monitor input.

Weather missing

Check latitude and longitude and network access.

Calendar empty

Check the iCal address is correct and public to the app.

PIR triggers constantly

Turn the sensitivity down and shield it from heat sources.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the smart mirror with weather and calendar?

Raspberry Pi 4 Model B (4 GB), Raspberry Pi 15 W USB-C power supply, SanDisk microSD card 32 GB (A1, Class 10), Raspberry Pi micro-HDMI to HDMI cable and PIR Motion Sensor HC-SR501.

How long does the smart mirror with weather and calendar take to build?

About 300 minutes for a intermediate maker, in 7 steps.

How do I know the smart mirror with weather and calendar works?

Power on: Mirror shows time and weather within a minute. Walk up: Screen wakes. Leave: Screen turns off after 2 minutes.

Blank screen: what should I check?

Check the HDMI cable and the monitor input.

Weather missing: what should I check?

Check latitude and longitude and network access.

Calendar empty: what should I check?

Check the iCal address is correct and public to the app.

PIR triggers constantly: what should I check?

Turn the sensitivity down and shield it from heat sources.