Projects / I2C between two microcontrollers

I2C between two microcontrollers

Beginner1 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANO

    Wire the bus

    A4 to A4, A5 to A5 and GND to GND between the two boards.

  2. NANO

    Add pull-ups

    Two 4.7 kΩ resistors, one from SDA to 5 V and one from SCL to 5 V.

  3. NANO

    Upload the target

    Flash the first sketch to the board that has the pot.

  4. NANO

    Upload the controller

    Flash the second sketch to the other board and open its serial monitor.

  5. NANO

    Turn the pot

    The serial monitor shows values from 0 to 1023.

  6. NANO

    Watch the LED

    The target's built-in LED toggles every half second as commands arrive.

  7. NANO

    Scan the bus

    Run an I2C scanner on the controller and confirm 0x42.

In short

How do you build an I2C between two microcontrollers?

One Arduino acts as an I2C controller and another as a target that returns a sensor reading. You need Arduino Nano × 2, Potentiometer 10 kΩ, Resistor 4.7 kΩ × 2, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm) and USB A to micro-USB cable (data) × 2. It takes 7 steps and about 60 minutes.

Level
Beginner
Time
About 60 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Controller A4 (SDA)Target A4 (SDA)Data line
Controller A5 (SCL)Target A5 (SCL)Clock line
Controller GNDTarget GNDCommon ground, required
4.7 kΩ pull-upSDA to 5 VI2C needs pull-ups
4.7 kΩ pull-upSCL to 5 VI2C needs pull-ups
Pot outer pinsTarget 5V and GNDReference
Pot middle pinTarget A0The reading the target reports

Code

Arduino IDE, board "Arduino Nano" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones). Uses the Wire library. The second sketch is written as comments so both can sit in one file here. Copy it into its own sketch and remove the // marks. Run an I2C scanner on the controller to confirm that 0x42 is found.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// ===== TARGET sketch (the board with the pot) =====
#include <Wire.h>
const byte MY_ADDR = 0x42;
volatile byte command = 0;

void onReceive(int n) {
  while (Wire.available()) command = Wire.read();
  if (command == 0x02) digitalWrite(LED_BUILTIN, HIGH);
  if (command == 0x03) digitalWrite(LED_BUILTIN, LOW);
}

void onRequest() {
  int v = analogRead(A0);
  Wire.write(highByte(v));
  Wire.write(lowByte(v));
}

void setup() {
  pinMode(LED_BUILTIN, OUTPUT);
  Wire.begin(MY_ADDR);
  Wire.onReceive(onReceive);
  Wire.onRequest(onRequest);
}
void loop() {}

// ===== CONTROLLER sketch (upload this to the other board) =====
// #include <Wire.h>
// const byte TARGET = 0x42;
// byte count = 0;
// void setup() { Wire.begin(); Serial.begin(9600); }
// void loop() {
//   Wire.beginTransmission(TARGET); Wire.write(count % 2 ? 0x02 : 0x03);   // toggle the target's LED
//   Wire.endTransmission();
//   Wire.requestFrom(TARGET, (byte)2);
//   if (Wire.available() == 2) {
//     int v = Wire.read() << 8; v |= Wire.read();
//     Serial.print("Pot: "); Serial.println(v);
//   }
//   count++;
//   delay(500);
// }

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Pot at one endReads near 0
Pot at the other endReads near 1023
Target LEDBlinks at 1 Hz
Unplug SDAController reads nothing

If it does not work

Scanner finds nothing

Check SDA and SCL are not swapped and that the grounds are joined.

Reads zero constantly

The pot middle pin is not on A0 on the target.

Garbage values

Wire.read order is wrong. The high byte comes first in this code.

Bus hangs

A pull-up is missing or both boards are set as the controller.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the I2C between two microcontrollers?

Arduino Nano × 2, Potentiometer 10 kΩ, Resistor 4.7 kΩ × 2, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm) and USB A to micro-USB cable (data) × 2.

How long does the I2C between two microcontrollers take to build?

About 60 minutes for a beginner maker, in 7 steps.

How do I know the I2C between two microcontrollers works?

Pot at one end: Reads near 0. Pot at the other end: Reads near 1023. Target LED: Blinks at 1 Hz.

Scanner finds nothing: what should I check?

Check SDA and SCL are not swapped and that the grounds are joined.

Reads zero constantly: what should I check?

The pot middle pin is not on A0 on the target.

Garbage values: what should I check?

Wire.read order is wrong. The high byte comes first in this code.

Bus hangs: what should I check?

A pull-up is missing or both boards are set as the controller.