Practice

GATE and placement practice

Short electronics questions with the working shown. Open each one in a tool and check the answer yourself.

59 questions

  1. GATECircuits

    Three 6 Ω resistors are connected in parallel across 12 V. What is the total current drawn from the source?

  2. GATECircuits

    A source of 10 V with 2 Ω internal resistance feeds a load. For maximum power in the load, what should the load resistance be, and what is that power?

  3. GATECircuits

    A series RC circuit has R = 10 kΩ and C = 100 nF. What is its time constant?

  4. PlacementCircuits

    Two 100 Ω resistors in series are connected to a 5 V supply. What voltage appears at the midpoint between them?

  5. GATECircuits

    A series RLC circuit has L = 1 mH and C = 1 µF. What is its resonant frequency, to the nearest hundred hertz?

  6. PlacementCircuits

    A 60 W lamp and a 40 W lamp, both rated 230 V, are connected in series across 230 V. Which one glows brighter?

  7. GATEAnalog

    An ideal inverting op-amp amplifier has Rin = 1 kΩ and Rf = 10 kΩ. What is its voltage gain?

  8. GATEAnalog

    A silicon diode conducts when forward biased. About what forward voltage drop do you assume in hand calculations?

  9. PlacementAnalog

    An LED drops 2 V at 10 mA and is run from 5 V. Which series resistor sets that current?

  10. GATEAnalog

    In a common-emitter BJT amplifier in the active region, the base current is 20 µA and β = 100. What is the collector current?

  11. GATEAnalog

    A full-wave bridge rectifier is fed from a 50 Hz supply. What is the ripple frequency at its output?

  12. PlacementAnalog

    Which feedback do you use in an op-amp circuit to keep its output stable and its gain set by resistors?

  13. GATEDigital

    How many 2-input NAND gates do you need at least to build a 2-input AND gate?

  14. GATEDigital

    What is the minimum number of flip-flops needed for a counter that counts 0 to 9 (a decade counter)?

  15. PlacementDigital

    Convert the binary number 1011 0110 to hexadecimal.

  16. GATEDigital

    What is the 8-bit two's complement representation of −5?

  17. GATEDigital

    A 3-to-8 decoder has an enable input and three address lines. How many output lines are active at once when it is enabled?

  18. PlacementDigital

    Which gate gives a 1 only when its two inputs are different?

  19. GATEDigital

    A D flip-flop has D = 1 and the clock gives a rising edge. What is Q after the edge, and what if D changes to 0 before the next edge?

  20. PlacementMicrocontrollers

    On an Arduino Uno, which function sets how a pin behaves as an input or an output?

  21. GATEMicrocontrollers

    A 10-bit ADC has a 5 V reference. What voltage does a reading of 512 represent, and what is one step?

  22. PlacementMicrocontrollers

    Why do you add a pull-up or pull-down resistor to a push-button input?

  23. GATEMicrocontrollers

    A timer runs from a 16 MHz clock with a prescaler of 64. What is the tick period?

  24. PlacementMicrocontrollers

    Which serial protocol uses two wires, SDA and SCL, and gives each device an address?

  25. PlacementMicrocontrollers

    What does this loop do on a board with a LED on pin 13? void loop() { digitalWrite(13, HIGH); delay(500); digitalWrite(13, LOW); delay(500); }

  26. GATESignals

    According to the Nyquist criterion, what is the minimum sampling rate for a signal whose highest frequency is 4 kHz?

  27. GATESignals

    An RC low-pass filter has R = 1.59 kΩ and C = 100 nF. What is its cutoff frequency?

  28. GATESignals

    A sine wave has a peak value of 10 V. What is its RMS value?

  29. PlacementSignals

    A square wave has a period of 20 ms. What is its frequency?

  30. GATESignals

    An amplifier's gain is 40 dB in voltage. By what factor does it multiply the input voltage?

  31. PlacementSignals

    A PWM signal at 5 V has a 25% duty cycle. What is its average voltage?

  32. PlacementCircuits

    An LED drops 2 V at 10 mA and is run from 5 V. Which resistor is closest?

  33. PlacementCircuits

    A 9 V battery is connected across a 450 Ω load. How much power does the load use?

  34. PlacementCircuits

    What happens to the capacitance of a parallel-plate capacitor if you double the gap between the plates?

  35. PlacementCircuits

    Two capacitors, 10 µF and 10 µF, are in series. What is the total?

  36. PlacementCircuits

    What is the effective resistance between two ends of a 1 kΩ and a 3 kΩ resistor in parallel?

  37. PlacementAnalog

    A diode has a 0.7 V drop. A 5 V supply feeds it through a 430 Ω resistor. What current flows?

  38. PlacementAnalog

    An inverting op-amp has Rf = 100 kΩ and Rin = 10 kΩ. What is its voltage gain?

  39. PlacementAnalog

    Why is a flyback (freewheel) diode placed across a relay coil?

  40. PlacementAnalog

    In a bipolar transistor used as a switch, what is the main job of the base resistor?

  41. PlacementAnalog

    A 7805 regulator has 12 V in, 5 V out, and supplies 200 mA. How much power does it turn into heat?

  42. PlacementAnalog

    What does a low-pass RC filter do?

  43. PlacementDigital

    How many bits are needed to count from 0 to 99?

  44. PlacementDigital

    What is the binary value of decimal 45?

  45. PlacementDigital

    A NAND gate has both inputs tied together. It then acts as which gate?

  46. PlacementDigital

    What is the main difference between a latch and a flip-flop?

  47. PlacementDigital

    A 4-bit synchronous counter is clocked at 1 kHz. What is the frequency at its most significant output?

  48. PlacementDigital

    In a 3-input AND gate, how many input combinations give an output of 1?

  49. PlacementMicrocontrollers

    An Arduino Uno has a 10-bit ADC with a 5 V reference. What voltage does a reading of 512 mean, roughly?

  50. PlacementMicrocontrollers

    Why does a push button wired to a microcontroller input usually need a pull-up or pull-down resistor?

  51. PlacementMicrocontrollers

    What is switch bounce?

  52. PlacementMicrocontrollers

    UART at 9600 baud sends 8 data bits, 1 start bit and 1 stop bit per byte. About how many bytes per second is that?

  53. PlacementMicrocontrollers

    Which protocol uses only two wires (a clock and a data line) and addresses devices by a 7-bit address?

  54. PlacementMicrocontrollers

    When is an interrupt a better choice than polling a pin in a loop?

  55. PlacementMicrocontrollers

    An ESP32 GPIO runs at 3.3 V. What can happen if you connect a 5 V signal straight to it?

  56. PlacementSignals

    What does the Nyquist rule say about sampling?

  57. PlacementSignals

    A 1 kHz sine wave has a peak-to-peak of 6 V. What is its amplitude (peak)?

  58. PlacementSignals

    A signal falls from 2 V to 1 V at the output of a filter. By how many dB did it drop?

  59. PlacementSignals

    What is the benefit of a Schmitt trigger input on a noisy slowly rising signal?

Questions are written for revision and are not past papers. Always confirm values with the official GATE syllabus.